Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello Nordic Team,
We have developed a custom PCB using nRF9151 and nPM1300 . Sometimes, the PMIC powers up and works normally; other times it doesn’t start at all. It occasionally...
Hi All
I have a question here.gatt Characteristic uuid has been Modified After the equipment has been in run for some time.
Current conditions of the equipment:
1.The...
Hi all,
I'm trying to use SPI Slave on a proprietary Hardware that use Ezurio BL54L15 (that contain a Nordic nRF54L15 chip). The environment is VSC + nRF Connect SDK 3.1...
Hello Nordic team,
I’m using the Mikroe nPM1300 PMIC Click Board (based on the Nordic nPM1300 PMIC ) with an ESP32 over I²C to charge a Li-ion battery.
Setup details:...
Hi,
May I know if the ncs add-on sdk-ant also supported nRF52833 because it is not mentioned in the list. Thanks.
Compatibility — ANT for nRF Connect SDK documentation...
Hi,
I need to use GRTC channel 0 in a nRF54L15 project. Channel 0 is special. It is the channel that the INTERVAL register controls. `zephyr/boards/nordic/nrf54l15dk/nrf54l_05_10_15_cpuapp_common...
Hello,
I’m designing a wearable device based on the nRF52832. To maintain time and date when the MCU and other sensors are completely disconnected from the 3.3 V supply...
Hi, I have an issue with nrf52DK, I cannod flash new version of my software. I have an error in VS Code:
* Executing task: nRF Connect: Flash: Aurora-nrf52/Aurora-nrf52...
Hello,
I am using Nordic nRF Connect SDK v3.1.1 and nRF5340DK board. My project is based on the project: GitHub - nordic-auko/nRF5-ble-timesync-demo: nRF52 clock synchronization...
Hi,
Has there any good course or training you recommend developing with LE Audio Development Kit either through Nordic official training or your preferred training program...
We observed a problem with our three different prototypes:
When there is only 5V-VBUS connected, the npm1300 does not ramp uo its voltages properly. The voltage rises up...
Hi there!
May I know how to have UART00 on P2 like what is shown below as I wanted to have higher speed.
Is it the same as other UART assignments on P0 and P1?
Thanks...
Hi Nordic team,
I'm currently testing the nRF9151 DK with a Conexa IoT SIM card in the United States (Philadelphia area). The board is flashed with the Asset Tracker v1...
Hello,
I a doing a ticket because I don't understand why my dht sensor doesn't fetch with my nrf54L15DK board.
Here is my overlay file :
/*
* Device Tree overlay...
