Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi,
I have my device based on the nRF52840 and it is working fine but we are focusing some issues given by our users.
When our device is connected to a smartphone, the...
Hi
I am having trouble changing the MTU size. I am using SDK 15.3 on nRF52832. I am developing a combined peripheral/central application, but I only need Data Length Extension...
Hi there,
I'm wondering if I need to have an SPM configure permission for my untrusted firmware to communicate with the environmental sensor via I2C.
I'm presently trying...
Hi,
I have a working project and want to use I2C 2 instead of UART 2. I have changed the .dts file:
/* &uart2 { status = "okay"; current-speed = <115200>; tx-pin = <29...
Just wanted to share my project of controlling the position of feedback servo motor with Nrf52840 by sending bluetooth commands using nordic toolbox
github.com/.../Feedback...
I used the mpu6050 sensor and did it according to 1.2 of this blog .
The driver of this sensor is in the ncs\zephyr\drivers\sensor\mpu6050 directory.Error after compiling...
SDK: NCS 1.4.0
board: nRF9160-DK
sample: lwm2m_client
# registration CoAP packet
In option enum, there is no "others". Where can I get this information?
I'm writing an application that transmits data over a mesh network of nRF52840 microcontrollers using OpenThread. I'd like the microcontrollers to prioritize sending MLE traffic...
I want to upgrade my application from v1.4.2 to v.1.5.1. but the Bluetooth init failed. So I tested with the scan_adv, which uses the same logic as my application. This also...
The device communicates okay with JLINK commander v7.00a although at the beginning it always says "Connecting to J-Link via USB...Out of sync , resynchronizing... J-Link communication...
Development Environment: icore7 laptop running Ubuntu 20.04.2 LTS.
Target: To build connectedhomeip sample application for arduino nano 33 ble board and check against laptop...
Hi,
We are building our project with nRF52811 and Segger Studio V5.34. (I have Ubuntu 1804 if it helps.)
We have certain variable configurations but would like the ability...
Hello Team,
My end goal is to send 0 to 600hz signal over Ble using NRF52832[ as explained below image].
So, for this, I have used this GitHub code
https://github...
Hello,
I am working an a product based on the NRF52832 and I need to trigger an interrupt when a capacitive button is pressed / proximity detected (BLE is peripheral and...
