Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Good afternnon, my company is utilizing a board with a nrf52 chip + softdevice, we would like to start unit testing our framework and just overall use cases.
After researching...
I am building a Zigbee network of devices where the devices are moving around quite a bit. This means the routes from nodes to the gateway need to be repaired often. I know...
Hi ,
We are going to update our mesh software via DFU, follow the step of mesh 5.0 SDK DFU guide. we success build bootlader , data page, and dfu demo app ( Set NRF_SDH_CLOCK_LF_SRC...
I'm attempting to download the network core image using the procedure described in "Programming the network sample from SES". My app prj.conf file includes the following statements...
Hi all,
Just have a few Asset tracker questions if anyone knows the answer:
1) If using the nRF Cloud, and a custom env_sensor, what's the maximum length databuf that...
I have an NCS project compiling and running for nRF52840 (nrf52840-DK) and am attempting to transition this project to nRF5340 (nRF5340-DK). (Prior to this, I tested the nRF5340...
I've just received a new NRF5340-DK and am trying to compile and test the 'peripheral_uart' sample.
I'm using SDK 1.50.
When I loaded it into Segger via "Open NRF connect...
I have a problem with nRF5340 :
when building with west build -bnrf5340dk_nrf5340_cpuappns -p so I have a clean build and flash after that with west flash everything is...
I have an nRF52840 acting as a SPI slave to another processor. If I put the nRF52840 into a deep sleep mode, how can we wake it back up over SPI? I typically have only seen...
Hi Team,
SDK- nRF5_SDK_17.0.2_d674dde
SD - s112_nrf52_7.2.0
chip - nRF52810
I would like to reduce the power consumption during systemON by disabling unused...
Please note that I am a new developer.
I am currently testing on a nRF52 DK on Windows.
I want to flash my application (which has a SoftDevice) and also write manufacturing...
Hello,
We have a lot of boards (more that 5000) witch embedded a nordic NRF51822 to scan beacons.
the person who designed the card did not plan any bootloader on the NRF...
Hi there,
I'm new to using an ATE and a NRF52 and I'm trying to use an ATE array with telnet commands to program firmware on 10 devices. After the firmware is applied, our...
Hi,Nordic!
I have a strange problem. I program custom boards. I can successfully program the application core with segger, but I can't erase and program the network core...
SDK 14.2, NRF52840, S140, NRF Connect for iOS iPad (v2.4.8)
We are sending a value to a characteristic as a request using the NRF Connect app, and then our NRF BT device...
