nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi all, I am using SPIM with dma list triggered by gpiote. A gpio low-to-high event starts spim reading, and it works fine. However, I need to read different length at different...
Hi,
I am getting following problems while executing ble_gls example.
1.device gets disconnected immediately after connecting
2.getting timed out error problem
Kit...
Hello DevZone Developers,
Presently, I am trying to find H/W which support BT 5.1 Direction Finding.
I came across this , where it is mentioned that "Nordic Semiconductor...
Hello
I am contacting you because I have a problem with the "otThreadSendDiagnosticGet()" function. In my program, I am trying to retrieve the list of RLOC16s of the children...
Hi,
As I mentioned in the title, I am using the `pc-ble-driver-py` python package which is basically bindings to the SoftDevice running on the nRF52840 dongle.
Here...
hello Nordic
i am using nrf52840, sdk 16.0, working base on the peripheral app_ble_blinky example
i wish to use the p0_11 pin for pulse generation (not pwm), but when...
Hi,
We are running the smp_srv on the nrf5340 NET Core, we suspect the example is writing the firmware image to the NET core instead of the APP core. How do we have to modify...
Hello all! Where is located the i2c example for the nrf51822 device? I am using the nRF5_SDK_12.3.0 . And i can just find and i2s example. Best regards!
Hello. I'm currently developing a software for nRF52832AA device. It needs to communicate with external device via UART. It resieves text message and takes some data from...
Hi there,
My question refers to the nRF SDK: examples\dfu\open_bootloader\main.c
When the example is built, the output HEX file contains a section that writes the Bootloader...
How do I get putty to receive output from the Thingy91? I see output in the LTE Link Monitor with the following prj.conf config:
CONFIG_USE_SEGGER_RTT =y
CONFIG_RTT_CONSOLE...
Hi!
My apologies if this question has been asked and answered previously (searched, but didn't find).
We are still developing with ncs version 1.3.2, but would like to...
Hi,
can someone tell me the correct order of AT commands to connect to LTE, activate PSM?
My findings so far:
AT% XSYSTEMMODE=1,0,1,0 => set LTE-M and GPS mode...
Hello, i'm using NCS 1.4.99 with a nRF5340 and i'm trying to use BLE and radio synchronization in the network core. My code run can run minutes without problem but sometime...
Hi,
I am trying to implement the AWS Discovery Sequence with the nRF9160DK board as the AWS Greengrass connected device. I am using the nRF Connect SDK v1.4.0 and used the...
