Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
I am using the nRF52840 and the nRF Connect desktop.
the nRF52840 serial number could be recognized like this.
the nRF connect BLE and programmer like this.
what...
Hi,
I tried to run the code which was used by another forum user:
https://devzone.nordicsemi.com/f/nordic-q-a/63149/nrf5340---p0-10-not-working-as-spim-miso-on-non-secure...
Hi, everyone
I am developing a BLE product with NRF52840 base on SDK 15.2.
Due to the cost of the product, we are now evaluating the feasibility of migrating from NRF52840...
Hi,
I am testing curve25519 in M52810.
The following is snippet.
nrf_crypto_ecc_curve25519_private_key_t bob_private_key; nrf_crypto_ecc_curve25519_public_key_t bob_public_key;...
Hi Dev Team,
I had a task to work on that required a timsetamp to schedule a certain event, like for example I wanted my modem to start off every morning at 10:00:00 and...
Hi,
I am using Thingy 52 to measure the acceleration from accelerometer. I was expecting values like m/s2 but I am seeing values in unit vector, ie, values between (0 -...
I have nrf52dk (nrf52832) board and a custom nrf52805 board. The nrf52805 board has no external 32kHz crystals, but only 32MHz crystal. Also, it is in LDO mode (no DC-DC inductors...
Device nrf52832, nrf5_SDK_for_Mesh_v3.2.0_src with nRF5_SDK_15.3.0_59ac345
Hello.
I want to transmit and receive some data between smartphone app and mesh sensor.(almost...
Hi, Im using nRF52840 DK, Segger Studio v4.52 and SDK version 17. I have been trying to make BLE OTA DFU work but have had many problems along the way. I followed the guides...
Hi folks,
I need a production test of an nRF52840 module at PCB level. Our board connects near instantly with nRF Connect + Bluetooth Low Energy, and displays its device...
Hi,
I am trying to implement wireless power transmission. For sending output voltage information from receiver board
to transmitter board continuously which of you module...
Hi, I am getting link time error in segger when i building a pre-built library with zephyr for NRF5340.
Error says,
c:/gnuarmemb/bin/../lib/gcc/arm-none-eabi/8.3.1/.....
HI. I have modified "usbd_ble_uart" a little bit and have changed the BLE service for transfering the received data from USB over BLE. The problen is now, the BLE service...
