nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hello ,
I am trying DFU over BLE.I am using SDK 14.0.2 .
i Flashed Bootloader Code and Softdevice 5.0.0 .then Device is Starting Advertised as DfuTarg and As Mention in...
Hello,
i have one nrf52840 board with a coded phy scanner and another sending advertisings, when it are close , i received in the scanner 100% of Advertisings, but when...
Hello,
I'm doing some initial investigation with the nrf9160 DK and after some reading and testing, it's clear that significant part of the low-power capabilities is determined...
Hi, I'm using nRF52 DK (nRF52832), demo code <TWI sensor>. I'm using this slave sensor to communicate with Master nRF52 DK. My code gets stuck at sensor_set_mode() function...
Hi,
I am trying to test the eligibility of updating my project from SDK 16.0 to 17.2 using DFU. I programmed just softdevice and bootloader of SDK 16.0 and made a package...
Hello All ,
I want to use timer 2 of nRF52810..my code is not giving any error but timer is also not going to IRQ handler...but if i made the same changes for timer 0 it...
Hello,
I'm using Seeger Embedded Studio and S132.
I'm trying to include ble_nus.h to ble_app template and compiling. But it gives this error:
2> In file included from...
hi,
I have following setup test cases .
Case 1 DK2 , DK1 Initialized with CLI directly
1a DK2 , DK1 Directly connected to CLI Every Thing Works
1b DK2-to-DK1-to-CLI...
Hi,
I am checking the voltage range on the input pins of the Nrf52832. The specs show VIH is 0,7*VDD and VIL is 0,3*VDD. I'm using the Nrf52DK, which has about 2.8V VDD...
Hello again,
This time I am trying to read HID reports using bluetooth to get the state of the caps lock.
I know this should be super simple and its explained in the hid...
Hello, dear developers!
Tell me the solution to the problem, how to properly initialize the SPI peripherals so that the program does not hang while waiting for the end of...
Dear All,
I'm using nrf52840-DK for development purpose of IEEE 802.15.4 standard. One is used as transmitter, while other as receiver. I'm using nrf_radio_driver inside...
Hi, I found that there is a BLE_HCI_DIFFERENT_TRANSACTION_COLLISION when I use nRF52832 in secure connections. The connection would disappear in 32 secs, but there won't be...
There's a Bluetooth mesh sensor server, which realize, for example:
present ambient temperature property and
desired ambient temperature property.
A Bluetooth mesh...
