Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
I would like to ask if it is possible to use both Radio and NVMC at the same time (no SoftDevice)?
My scenario:
Start Radio and configure RX mode.
Write/erase...
Hello
I use nrf52840, Keil uvision 5.26, Win10.....
when i test the board, program run into hardware fault.
that reason is No I2C response, and i delete int the I2C...
I am developing a device which will have Nordic's UART service and it also need to be able to bond with the central. I am using SDK 12.0.0 and VisualGDB for my previous projects...
I'm working on getting an eclipse project working for my nRF52840 application that is currently working with a Makefile. My issue is that once I reset the board, or power...
Hi below is the function i am using to run garbage collection after deleting the data but the result i am getting was the same as before garbage collection.
I mean DIRTY_RECORDS_BEFORE_GC...
I have the following questions about PM and what it generates. My relevant board and config files are below, along with the PM partitions output.
1. Can you explain the...
I am using SDK v17 and Segger v4.52 but for some reason none of the print statements are being printed in the debug terminal. I think I had to enable these two things in sdk_config...
I am sending or trying to write character to ble_app_template but its giving error and its not receiving character.
this what i am trying to send-
if(strcmp((const char...
I see an ID that queries or prints RSRP/RSRQ/Cell ID-related information, but I don't see the AT instruction sq.E. for SINR, where can I print SINR information?
Hello guys,
Just received the Thingy91 and trying to upgrade the model firmware to v1.2 but it fails like this:
However I successfully been able to flash the modem firmware...
Hi Team,
We are using the nrf52840 soc for our application along with crypto engine (mbed TLS ) along with RNG, ECC, SHA256.
While validating the digital signature with...
Hi,
Do you have any direction finding evaluation kits for now? Although I saw many similar questions and until four months ago the answer is still NO, but I still want to...
we'r developing our product based on nRF51822 and also using BLE(Bluetooth) as wireless device.So, we want to release our first product in this year in markets. The next steps...
Hi Forum, 1.) The APP_ADV_... parameters in ble_advertising (SDK 16.0) are taken only from _fast_ , is this intended?
2.) s113 allows only TX_POWER of 4dbm, although the...
I would like to flash certificates in production.
My plan is
First, flash an app for installing parameter like client id using nvs and certificates.
Then, flash a production...
