Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Thanks in advanced. On sdk17.0.2 examples\ble_central\ble_app_uart_c, I connect a button's one end to nrf52832 pin 24, the other end is connected to VDD. So I have to #define...
Hi,
There is an option CONFIG_LTE_NETWORK_TIMEOUT for the LTE Link Control. The default is 600 seconds (10 minutes) but I couldn't find any suggestions for the timeout and...
Hello ,
Now I am sending the data per 7.5ms in the interval of time over ble .I am loosing the packets , to avoid this I am planning to send the data in the structure .How...
Hi,
I got a unit based on NRF52 (No matter what SDK) which is connected via 1-wire (dallas protocol which is very time accurate) to other unit.
The other unit is the master...
Hi! I wanted to ask someone who knows more than I, if this setup makes sense, and how I could test my design.
A bit of background: We're developing a custom board which...
Hello, I am using nrf51822 / SDK 12.3 / SD 130-2.0.1.
When a normal timer is set and softdevice off, the timer interrupt does not occur.
In SDK 10 / SD 110-8.0.0, timer...
Hello,
I am trying to use the flash API of fstorage in my code. I have called below function at the start of my code. I want to save some integer values every 1 min interval...
Hello
I am trying to read a characteristics from my peripheral using my central. From what I read here, I have to use sd_ble_gattc_read(). Is it correct ? But I did not...
Hello
We have produced boards with a Telit module using the nRF52832 chip.
Our software developper have a lot of problems making the connexion and communication reliable...
Hello,
After a long war trying to connect MPU6050/MPU9250 to NRF52 DK with nrf52832 on board, I finally succeeded and I am getting values through UART.
But I have 3 problems...
Hi,
I would like to get the stored CCCD values of a bonded peer using pm_peer_data_load()
I am currently struggling with the format of the data returned by pm_peer_data_load...
Hello.I am a graduate student at Nanjing University of Posts and Telecommunications in China.My question is, does your company provide the source code of the Bluetooth mesh...
To the kind attention of Nordic support team,
we are doing ble bonding using passkeys.
We noticed that when starting the passkey phase, a ble connection event is generated...
I am not able to run commands with nrfjprog using the J-link Segger device
e.g. nrfjprog --family nrf52
I can do it only with the Keil or Segger UI environment
How can...
hello
right now i am sending 100 plus data per second i want to print millisecond at each data how can i acheive this is there any program in nordic or github i can use...
