According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi,
I am try to configure internal RC (LFCLK) but device hang in "sd_softdevice_enable(&clock_lf_cfg, app_error_fault_handler);" API.
Changed in "sdk_config.h" to enable...
Hi
When we enable the ADC on the nRF9160, we se a considerable rise in current consumption in standby mode, from sub-100 µA to several hundreds of µA (~400 µA). How do we...
Now that most or all of the Nordic nRF5 SDK is covered by the permissive 5-clause Nordic license (as of June 2017: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hi
we are working on ble_nus_c multilink implementation and had problems when more than 1 server is connected: we've noticed that data get mixed between servers.
when...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
Is there any sample code integrated with HDC2010 Temperature & Humidity...
Hello,
I use a debugger probe (Segger Jlink) with the sdk_config.h setting SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL.
When my probe is not connected, there my product is blocked...
Hi, I am new to Nordic BLE development and trying to create an application that has beacon functionality with firmware upgrade over the BLE with the mobile phone and Nordic...
Hi,
So I've been developing just fine on the latest V1.0.0 SDK and SES 4.18. I literally stopped and started a new debugging session and suddenly SES is trying to reflash...
Hello!
I have 3 NRF52840 Preview DK's with Q1AAAA revision ICs. I have been putting those to good use, but I want to test some stuff with SPIM at 32Mhz, which I understand...
Hi,
I am using nRF9160DK, nrf v0.4.0, zephyr v1.14.99-ncs1
I have been trying to measure the boot time from when I press the reset to when it gets to the start of the...
Dear All,
I am trying to enable brown out detection to my NRF9160. From what I see in the data-sheet there is a register that you can set the brownout threshold, but there...
Hi,
looking at the ifx_optiga_custom_example in the nRF5_SDK_15.3.0, i see that for the Hashing calculation the oberon backend is used instead the optiga backend, Why? Is...
Hi,
I see your web: https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Sniffer#infotabs
There are 4 hardware (DK x 3, Dongle x 1) we can choose to used...
Hi,
I am using nRF52832 with sdk15.3 SES
I need to use DFU.
Buttonless DFU
need to program the controller without the wire connection.
Can you explain how DFU works...
