Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I am building a project that required pwm drivers and BLE UART. I started by using peripheral ble uart example in SDK 12 and adding the pwm driver source file from...
I'm in need of some help with connecting to the Thingy 52 when using Windows 10, in this case Windows 10 Pro. I've tried Google Chrome and Opera.
If that helps, I have...
Hi,
I'm using sdk14.2 peripheral examples fds and fstorage in an attempt to test flash storage persistance (with softdevice present).
The two examples are quite intuitive...
Is there any way to invert the PWM behaviour easily? I'm trying to develop firmware that will run on the DK52 (LED active high) and my custom board (LED active low).
I...
Like it says in the title. I'm working on an embedded application where lifetime is pretty important, so I'm trying to get power consumption down as low as possible. I don...
I have Rx sensitivity issues when DCDC is enabled
The 52832 datasheet shows these connection:
DCC: 10 uH,
DEC4: 15 nH
When switching both inductors I get better sensitivity...
Hi, I am have been using PPI to control SPI transfer in response to a GPIO interrupt.
The PPI initiated SPI transfer that reads an external device's register A and I would...
while the ble_uart example is a great resource of information, i have a need to completely separate the ble nus data in / out from the hw uart code
using sdk 14.2.0
...
Hi everyone,
So I've this arduino code that utilizes the I2C library and made some convertions to it to work with the nrf52832 in the segger embedded studio and when debugging...
Hello, I'm trying to migrate an Atmel project to nrf51822 chip.
Now, in the original project there were 2 CB arrays registered, one dealing iwth GATT one with GAP:
a...
hi,
I am working on nrf51822 chip and using sdk11.0.0 sdk,softdevice (s130 2.0.1) .I want to send 4Kb of data in a packet from the central device and on the other side my...
Dear all,
We have just purchased "nRF52840 Preview DK" kit for a project that connects BLE SoC to Linux host machine.
I have just realized that Connectivty example from...
Hi,
I managed to get fds to store some information in nrf51dk for persistent data storage. I would like to check if the data is still available in the chip after power...
Well, I have question for this SPI connection problem.
anyway,I have nRF51822 core board using adxl345 with SPI connection. that connect SDA to P5, SDO to P6, SCL to P7,...
