Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
i am testing the ble_uart programme. i am using the nRF51822Ek and soft device s130_nRF51_2.0.0 and nRF5 SDK v12.2.0 and keil uvision5 and nRF tool box (android).i am using...
Hi
I have the PPK, and I see it needs either a JLink or a Nordic DK board to act as the interface to the PC.
I have a nrf52832 dk and also nRF52840 dk, so I was going...
I made IAR work with nrf52 in monitor mode debugger. I also would like to try this to nrf51. I found nrf51 doesn't have DebugMon_handler......Please confirm can I single step...
Hi,
I am working with nRF51 for my application. I do not use softdevices. I need to have a random variable in my code. I have read Reference Manual and I have found that...
Does nRF51822 have battery monitor?
pg 45 of datasheet says specifies "Absolute error when used for battery measurement" at:
Internal reference, input from VDD/3...
In the nrf52 OPS datasheet, for NVM and flash programming electrical specification (page 41) it has "Amount of writes in a block between erase" and Minimum for that is 181...
Hi all.
I need some suggestion how to use UART module in the nRF52 using nRF5_SDK_12.2.0 and the softdevice $132(it would affect?)
I would like use RX to receive information...
Hi.
Didn't find an exact answer for my question.
I'm using the ble_app_beacon example on my custom board based on nrf51822. While powering it from a coin battery, I measure...
Greetings. This is a followup to my previous question BLE Software Configuration for FCC Spurious Emissions . I did not ask the right question there and I did not want to...
Help!! I need to implement a dc motor position control and i have problem reading the encoder (too fast). I have seen that nrf51822 has a qdec peripheral. Any suggestions...
Hi,
I wanted to know if the UART pins can cause any issues if kept connected to usb (Rx/Tx pins stable to 3.3V) and directly to the GPIOs of the nRF52, while performing...
I've come across the following situation:
We have a device (nrf52) which uses fast advertising with whitelist after it has established a bond with a single phone. When...
Dear All,
I'm kinda getting desprate and would be very thankfull if somebody could help me.
I want to get two NRF24l01+ to communicate with each other. But it doesn...
hi, all
I met a communication problem between nrf52832 and nrf24le1, I used nrf52832 as receiver and nrf24le1 as transmitter, but unfortunately，nrf52832 can not receive...
