Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello, I am using Nordic chip 82832 with sdk 17.1.0 and SoftDevice s132. I am facing an issue where a specific requirement requires my advertisement interval to be specifically...
Hello,
we would like to use the LPCOMP on the nRF54LM20A, but there's some confusion on which GPIO domain can be used.
According to the overview block diagram , LPCOMP...
Hello,
I'm working on a custom Zigbee End Device application where I want do some modification of the device announcement message. I've used NXP's Freescale Beestack Zigbee...
In Nora B-206(nrf54l15) not able to use port 1 pins 2,3 (P1.02/NFC1 P1.03/NFC2) as normal GPIO. TRIED :
& nfct {
status = "disabled" ; // Disable NFC to free P1.03 for...
Hi,
I'm using a custom code I developed to save all console logs to an SD card based on the Zephyr architecture. I originally developed it for the Thingy:52 and have also...
Under the old `nrfjprog`, it was possible to check whether the modem firmware matched a particular release by running `nrfjprog --verify mfw.zip` (see )
This is no longer...
Hi Nordic support:
We previously submitted a case about OTA testing in CMW500 connection mode. Following is that case:
We tried OTA testing with the CMW500 connection...
Hi everyone,
I’m starting a new project using the nRF54L15 MCU . I’ve worked with the nRF52840 and nRF52832 before, but this is my first time with the nRF54 series.
Due...
Hi,
I am using NRF52833 with soft device version s140. I have set the advertisement duration for the BLE app to 0 (meaning the duration is infinite). Also, I have set scanning...
Hello Nordic Support Team,
I am working on a project using the nRF52832 microcontroller with NRF5 SDK version 13. I have implemented the Flash Data Storage (FDS) module...
Hi Support Team
It seems that there is no current consumption information for SPI and UART of nRF54L15 in data sheet. We want to know the current consumption when SPI and...
I've made an Excel sheet to estimate the power consumption for my nRF51822 device.
Modify light-green fields, to fit your design and see what the estimated current is.
Please...
Hi,
1. I tried flashing all ble codes to my nrf kit. It does not seem to connect on Windows machine but connects on Mac. My other nrf kit connects perfectly fine. What is...
Hi,
I was wondering what I need to do, or if it is even possible, to debug a non-secure app which uses TFM.
Running 'west debug' on e.g. the blinky sample works regardless...
I’m running a self-built BLE application on the nRF52DK board. It used to work fine before, but recently it has stopped working. The board still runs all the sample codes...
