nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hello. Earlier we had nordicplayground/nrfconnect-sdk docker images for v2 (e.g. nordicplayground/nrfconnect-sdk:v2.9-branch ). But it seems there is no docker image such...
I have the revision 1.0.0 of the nRF54L15-DK. I want to use the SPI pins on the GPIO header P2. The datasheet says: nRF Connect for Desktop's Board Configurator application...
Hello,
After updating to the latest version of nRF Connect for VS Code, I encountered an error.
I am no longer able to erase, recover, or reset a board from within VS...
Hi,
we develop a battery powered device that has a battery charger ic. Can the ppk 2 measure negative currents in ampere mode when the battery is charged?
Hi all,
I have Nrf52 devices that use Nrf DFU with "Buttonless Secure DFU Service".
I would like to integrated the ability do to firmware update the devices to our "fleet...
For the nRF54L15, what is the voltage at the output pin of DCC (and input pins of DECD, DECA, and DECRF) in DC-DC mode?
Is it 0.9V? Is it constant?
Vinson
Hi,
We are using both nRF54L15 and nRF54L10 in our product, with DFU support where an external flash is used as the secondary partition on both MCUs. The hardware connections...
Dear Sir,
I am getting the below Error During building of LED Blink Program for nRF52840 Module using PCA10056. Below code I am Trying to run:
#include <stdbool.h> #include...
I am using the PPKII to supply a 1.8V supply for a circuit board in my measurement setup.
I have been battling a low-frequency oscillation at 0.5Hz at around 5mVpp, which...
Hello!
I want to make a self-test that verifies the speeds of the 32.768 kHz clock and the 32 MHz clock.
The idea is that if the ratio (976.56 to 1) is correct, then the...
I have started working with the nFR9151-DK board. After some time, I may have accidentally erased all data from the board using the PROGRAMMER application. As a result, the...
hi Nordic
i am working with nrf52840 and nrf52832 with ncs v2.8.0
i am also working on nrf54l15 (since nrf54h20 seems to not be fully integrated yet)
i want to know...
Hi,
I am trying to do t rilateration using one initiator and 3 reflectors. For now I am just trying to get 2 reflectors to work.
Sadly I cannot get the initiator to...
hi support team,
may i ask how to test 54l15+21540 dtm? i have send code to customer, but they feedback to me that the output power is 15db, not 20db(using serial send command...
Hello,
The customer, T&D would like to registrate their product to Bluetooth SIG.
Then, design number shoule be required, however, regarding SDK3.0.2, there isn't any...
