Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I got an error when trying to build the dimming_client_nrf52840 example.
Simple error:
build/dimming_client_nrf52840_xxAA_s140_7.0.1_Debug/obj/ses_startup_nrf_common.o...
SDK 16, S132 V7.0.1, NRF52832, custom device, custom firmware.
Hello,
I want to keep beaconing advertisement (not connectable advertisement) while the BLE is connected...
Hi,
I have a question concerning the SIG qualification. We use the ublox BMD-350 (nrf52832) that is qualified as a component (QDID 101018). I don't really understand the...
Hello,
We are using nRF52840 chip with S140 with ble_app_blinky example.
I was merging Serial DFU bootloader, SoftDevice, application and BLE settings with below commands...
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of Thread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure these...
Hi,
I wrote my codes to toggle notification on and off using a button using nRF25840-DK and sdk v15. The task looked a simple one; however, I hit some issues such as error...
Hello Nordic Team,
We are working on a project based on nrf51822, we have a problem regarding the incorrect ADC values while waking up the microcontroller from System...
Hello,
I'm developing a custom asset tracker board. My software is currently a very lightly modifed asset tracker v1; my provider currently only support NB-IoT, firmware...
After that one of Zephyr's configuration files was modified (CMakeLists.txt, *.overlay, prj.conf).
How the SES project can be updated in additional to option "Open nRF Connect...
I'm trying to use the board support package (BSP) through a keil software pack, starting from the dfu_dual_bank_ble_s110_pca10028 example. I thought it would be more or less...
Hello, I have installed (multiple times) the nRF connect SDK via the manual installation guide but I still seem to be unable to open any project.
I have tried on MacOS and...
Hello,
We are currently using SDK v17.0.2 with NRF52840, driving a display with SPIM3. We are able to successfully communicate with our display and command it to render...
Hello. I'm designing a board with NRF52832 connected to SGTL5000 via I2S. I'm planning to use the driver found in the Nordic Playground here...
https://github.com/NordicPlayground...
Hello,
Before going into detail, the question is: Is there is any chance that NAND flash will be supported (via QSPI or SPI) by the nRF5 sdk in the future ?
My question...
