Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I want to check which version of BLE is implemented while using a particular SDK or Soft Device(SD). Is the version of BLE dependent on SDK or SD or both ? I couldn't find...
Hi,
We encountered a problem if we take off the battery during functionning.
The UICR Register is completly erase when we put back the battery.
The issue is with lost...
Hi - I have a MDBT42Q SoC board developed by Seeed Studio which contains the nRF52832 SoC. The board is powered as the image below and I can program the board through the...
SDK: nRF5SDK Toolchain: ARM GCC
Hello,
I have some devices out in the field using nRF52840s, using the non-SoftDevice bootloader, and a custom mechanism for reading updates...
While the nRF5 SDK offers great support for validating the SoftDevice and application firmware in internal NOR Flash on every boot, it looks like that's not the case for the...
I am using nrf52 DK board with SDK15.3.0 developing my application on top of ble_blinky_peripheral example .
How do add CTS service in my application ??
I have refered...
Hi
I want to make use of this SD-card reader together with the nRF9160dk.
From what I understand:
1. I need to create a nrf160dk_nrf9160ns.overlay file to chose which...
Hi,
As in the subject, I cannot find where to change the optimisation level. I am working with the Zephyr bluetooth sample project - peripheral_hr.
I have found a previous...
Hi
I have register the esim of iBasis and its works relly well but I need know how to use a esim of a different company on nRF9160DK, I don't know if the location is important...
Hello,
I'm using a modified version of the examples->peripheral->radio examples from nRF5 SDK v17.0.0 to receive packets sent on Bluetooth Low Energy channel 37 using...
I use ble_app_uart_c.
I have a central(nRF52DK). I have a peripheral(nRF52DK). When i run my code, I would like to see my peripheral's name and it's UUID on the terminal...
I am using SDK 16.0.0, Soft Device S132 (v7.0.1) on a custom nRF52832 board.
I have a secure boot loader on board that is triggered by a buttonless OTA application.
After...
Hello. I'm in the midst of purchasing a power profiler to works with nRF51 Development kit and nRF51 USB Development Dongle. May I know if all the technical resources on nRF6707...
Hi there!
I am using the bluetooth/peripheral_hr sample as a basis for my application, on top of which I need to include the nrfx_qspi driver. However, I get a "undefined...
