nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
hi,
We are working on nRF9160 DK board.
One of the issues is how to save secure data (e.g, data key) into flash. Is there any examples or document on data storage APIs...
Hello,
i am developing on nRF52840 using SDK 15.2.0 and Softdevice 6.1.1.
I recently noticed, that when i first bond with the nRF52840, then disconnect and delete the...
Hello,
I am using nRF52840 development kit and I wanted to know with use of the source code of nRF blinky application can i modify as per my project requirement and make...
I am connecting debug out on the NRF52 DK to a production board for programming. I am using Tag Connect connection and need to make sure I route pins properly. I cannot find...
Good morning,
I'm developing a new product based on nRF52840 and S140 (v6.1.0). I'm able to connect using my smartphone using the following data:
sec_param.bond = SEC_PARAM_BOND;...
Hi, sorry for if this has been answered elsewhere.
I am currently designing the production setup for a product using the nrf52840 as a BLE radio.
I can't find how the...
Following this tutorial: www.novelbits.io/.../ some doubts arose in my head.
My doubts concern Android app witch name is: nRF Mesh. This application is used only for Provisioning...
Our BLE DFU has stopped working in SDK 3 so I have tried to simplify it by going back to SDKs.
If I compile D:\NordicSemi\nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\Examples...
Hi, I have a question about Bluetooth mesh secure provisioning, as it is described in the spec section 5.4.3.
The spec states that either
1) both OOB public key exchange...
We are looking to implement "dynamic" BLE services that can be configured (i.e. enabled/disabled) externally, however from the examples there appears to be no way of de-initialising...
Hi,
I have nRF9160 DK. I want to update firmware to (From Your WebSite: Link Pasted)
nRF9160 LTE-M/NB-IoT/GPS Modem firmware
https://www.nordicsemi.com/Products/Low...
Since nrfConnect Programmer, ninja flash/west flash ALL use nrfjprog behind the scenes, I wish I could find out _exactly_ which nrfjprog commands the nrfConnect Programmer...
Hi,
I'm trying to reduce the current consumption. I can't use sd_power_system_off because I don't want my device to rest when it wakes up. So the other way to do this is...
