Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I have a question about PeerManager.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) deviceA: EYSHJNZWZ (nRF52832) deviceB: Android (ver9...
Dear All,
We would like to automate the trst procedure of our device in LabWiew because in this tool we are doing also electrical measurements.
We have tried nRF connect...
Hello,
I'm running custom firmware on a nRF52840 based DK (Rigado BMD-340).
The log from the nRF Connect app is as follows:
Could anyone help explain the error...
Hi,
I am using nrf mesh sdk v3.2.0 and I would like to combine our custom service within the mesh server example (includes the proxy service). Using info from other threads...
We are having issues with UART communication on the nRF52840. Using a logic analyzer, we have found that the transitions happen too quickly. This causes the receiving MCU...
I have been working with Thingy:91 for three weeks now. Everything works nicely, however, I could not get any GPS location from it. I am using Rogers simcard which is a local...
Hello everyone. My project is getting quite complex so I will try to abridge. (Mesh SDK 3.2.0) I am trying to send wifi credentials from an android application (derived from...
Hi guys,
here in Croatia I'm trying to connect to NB-IOT network using nrf9160.
Here are the commands i am executing:
After this command modem does not accept any...
hi all,
i build project use HCI controller with nrf52840 , it some time show error message,
how to deal with this issue
HCI Host Not enough space in buffer #hci
https...
Hi,
I am working on a development where the values of a bunch of nodes with a sensor needs to be captured in one aggregator device in a mesh network. The aggregator then...
I tested ble_app_att_mtu_throughput_test code with 52840 EVB for BLE5 Long Range as below site.
( https://devzone.nordicsemi.com/b/blog/posts/testing-long-range-coded-phy...
Hi everyone,
I am trying to use the Port interrupts on the nRF52840. I started from the example "pin-change-int" and it works fine when I use one input pin.
But when I...
Hi,
We have a product composes of a central and a peripheral which uses Nrf52840 as their MCU and communicate with each other via BLE. The peripheral will send some data...
Hi,
what should I do in order to enable Bluetooth Low Energy on PC (mainly Windows XP to 8, but Linux or Mac would be nice if they don't support BLE natively)?
My device...
