Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I have four Bluetooth modules (servers) that measure pressure continuously. The servers should connect to the client and send the measurement data to the client. I can read...
Good afternoon,
We are developing a consumer product that is using the nRF8001 as the BT peripheral. We have a question regarding certification; do we need to undergo...
Dears，
To support Bluetooth 4.2 in the nRF51822 product page on S110, but only support 4.1 in the SDS document, I want to confirm the support of the S110 V7.3 and v8.0 for...
Hi,
for my application, I want the processor to wake up once every 8 hours, do a 1 second analog measurement, broadcast the results and shut down. When activated by a switch...
Hi,
I am having some trouble using fstorage to write data into flash. I want to store ~20 kB of sampled data before processing it, and I am storing it just below the bootloader...
Dear every one.
My company has ordered 20 development kit NRF52840 for our Mesh project. We will receive these board 1 week later.
But i have 1 preview development kit...
Could you please help me out on how to read my EMG sensor values and display it via the Nrf tool box. I have a redbear nano v2 and the digital output of the sensor is received...
Hello,
I'm having some issues with the MAXCNT limitation of 256bytes because I want to send larger packets and receive packets through the SPI Slave interface, which is...
I have an external board based on nRF51822 QFAC. I have a nRF52 preview DK. Will it be possible to detect my external board if connected via the preview DK. I tried and the...
Hello,
We've a Custom board based on nRF52832, it works fine in beacon mode using the Synth Clock (else it doesn't work):
// <o> CLOCK_CONFIG_LF_SRC - LF Clock Source...
When using the PPK to measure the current of our custom hardware the lowest range doesn't give logical results. (Either the PPK python GUI or nRF connect) When the nRF52 on...
Reference: nRF52840 DK Evaluation Board Schematics
The following inductors are lised in the schematic:
L1
3.9 nH
High frequency chip inductor ±5 %
0402 ...
I am working on windows xp command prompt and using nrfutil version 3.5.1
I want to do a Device Firmware Upgrade over BLE through my nRF52 DK board on a custom element....
