Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Hi,:
I run my application program by nRF51822, about S110 V6.0 and SDK 5.2.
When the program run servial cycle functioin , it is work normail.But sometime, nRF51822 sysytem...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello Guys,
I'm about to start my first BLE iOS project and I was wondering if there are any compatibility issues or anything that I should be aware between nRF51822 and...
im running on mac with eclipse and tried to use debugger prints, but the don't show up in the console.
Same goes for printf and uart.
Is there a flag in the makefile preventing...
Hello,
I am checking to see if it is possible to use app_twi_perform() to transmit TWI transactions that have a High Write bit. I have changed the polarity of APP_TWI_WRITE_OP...
I'm developing an embedded application using the nRF52 device. I am using GCC to build the C software and a segger flash device to program the nRF52, all using linux. I wish...
I wrote this code found in an example and it works fine:
#include "nrf_drv_config.h"
#include "nrf_drv_timer.h"
//Before I activated TIMER0, TIMER1 and TIMER2 in nrf_drv_config...
Hi,
I am using eclipse IDE and gdb to debug and flash applications onto nrf52 dk. I wish to be able to print data and messages to the eclipse console. I work on mac OSX...
I'm trying to send data over UART... started off using the examples from the SDK.
When I run the code on the dev board, I can get it working. When I load the code onto...
I want to use ESB protocol, with app_timer module to generate timer interrupts. Is it possible?
If yes could you please send some example codes for it? thanks
Per the nRF51822 product specification the NVMC ERASEPAGE operation takes up to 22.3 ms, about 730 ticks of a 32 KiHz clock. This is 365x the maximum delay between the watchdog...
For evaluating the nRF52 for a project I need to demonstrate BLE 4.2. secure pairing with NFC
I want to use two nRF52 eval boards but I need two software examples: One...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
