I made a custon pcb and until now it is working as expected . I am using the me54l14 module by minewsemi and i want to enable the CTE capabilities so that i can have angle...
Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello Everyone,
I have been working around BLE profiles for few months and i have made several tested for each service via MCP(android) everything works fine but now i...
Mt need is to do frequency measurement of 0.01Hz to 99.99 Hz
We need a clock of 1us that added to a timer of that start on when the pulse low to high event happens and...
Hi there,
I want to connect multiple nus devices to S120 central. After connection with device, it starts to scan again after the BLE_GAP_EVT_CONNECTED event. And there...
Hi,
I am using the s110 and SDK 6 and trying to have multiple notifications from different services/caracteristics. For now I have two services, one for the battery and one...
Hello, i have a strange situation here with TWI module and i have no idea what is happening. I have read a lot of posts here on devzone and the code i am using is also found...
Hi,
I am using nRF51822 spi as a master to communicate with the AFE. Four bytes need to transfer each read or write process. I use nRF51_SDK_10.0.0_dc26b5e.
Configuration...
hi
I am trying to gather information on what is needed to create a mesh network using BLE.
I am more familiar with Zigbee/Thread, but I am asked to implement something...
I downloaded S212 for nRF52 from thisisant.com and programmed the softdevice to nRF52832DK(PCA10040) via nRFgo Studio. Then I copied the 'include' folder of unzipped softdevice...
I have been trying nrf-sniffer with no success. Setup is:
Win7 64,
Sniffer Win 1.0.1,
Wireshark 1.10.14 (both win32 and 64 tried),
PCA10000 and PCA10001
The sniffer...
I generally upload codes from mbed.org to my PC then send the hex file to nRF51822 by nRF51-DK's pins. But I don't want to use cables to upload hex codes to nRF51822. Are...
Hi community,
When I want to use the example multilink peripheral inside the s120 directory example of the SDK 6.1.0, I'm not able to compile the code.
The device_manager_peripheral...
So, I want to make an application where my NRF52 advertises an URL via the Eddystone beacon.
The URL will link to an webpage, that will connect to my device through the physical...
As here said link1 If we want to use flash in the mesh we should ignore APP_ERROR_CHECK(NRF_ERROR_INVALID_STATE) in ts_sd_event_handler() ,
2.And here link2 tell us...
