I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
My product currently has DFU (Device Firmware Update) functionality enabled, but I want to allow firmware updates only after receiving a specific command via BLE. This is...
Hello Team,
i am trying to read multiple mcp9600 on the nrf9151 on my thingy 91x. I connected 3 of the mcp9600 to my stemma QT connector and it all works fine.
However...
i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello.
After some great struggles, we've managed to enable WiFi and encrypted socket + TLS connection to google.com and various websites.
Since then, we've been looking...
Hi,
We have used the internal clock successfully in the past in nrf5280 for 8MHz RF transmission, but when trying to do the same in nrf5340, we faced this problem:
Nordic...
Hi all,
I could not find similar questions raised on the forum and I hope someone can help me.
I have an application to connect to a mqtt server, developped on the latest...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
After completing the OTA update, I executed the "otasoftwareupdaterequestor read-event version-applied" command but was unable to read back the version.
I then tried the...
Hi,
I’m currently working with the nRF52833 together with the nRF21540 Front-End Module (FEM). I have configured the FEM to provide a gain of 10 dBm. I have a few questions...
Hi everyone,
I'm currently working on a BLE project using two nRF5340 DKs and would like to perform range tests to evaluate the maximum connection distance under different...
Hi, I have issue where the slot 1 image seems stuck. It can not be erased, confirmed, or swapped in the state that it is currently on. When I click erase, the error bad state...
Quick question.
Per the unique ID in chips from around a decade ago were not guaranteed to be unique.
I'm wondering if this is still the case for a given nRF5340 chip...
