According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hello guys, i'm new in nRF51 DK board, and i would like to flash the .hex file to my board, but when i do it the board automatically unmounting himself and reset with the...
hello there i want to send negative acknowledgement then what should i do?? like i want to send some data and then i want to send negative acknowledgement
i am trying to use yggdrasil for nrf51422 (pca10028) with sdk 10.0. after installing, i cannot see the com port. How do I flash "connectivity_115k2_with_s130_1.0.0.hex" with...
Hi everyone!. I am beginner for Nordic Devices
I want to use RTC Clock with softdevices
so I loaded the project ble_uart_s130 from examples.
and I changed code like...
I have a ble central device. Sending commands to UART in main() works well. Sending in on_ble_evt() doesn't work (only the first char).
But I see in your examples that you...
Hi guys,
I've almost got DFU working on SDK10. However I am having issues at post validation of the image, specifically in the function dfu_init_postvalidate() in file...
Hello all,
Thank you in advance for taking your time for reading this question. I'm developing a proximity application and I have programmed the nRF51 DK with the s110...
Hi,
I am trying to set up a small mesh network. Basically I have a couple of PCA10028 (v1.1.0) and I have flashed the mesh example:
github.com/.../BLE_Gateway
One...
Hello Everyone,
I have been working around BLE profiles for few months and i have made several tested for each service via MCP(android) everything works fine but now i...
Mt need is to do frequency measurement of 0.01Hz to 99.99 Hz
We need a clock of 1us that added to a timer of that start on when the pulse low to high event happens and...
Hi there,
I want to connect multiple nus devices to S120 central. After connection with device, it starts to scan again after the BLE_GAP_EVT_CONNECTED event. And there...
Hi,
I am using the s110 and SDK 6 and trying to have multiple notifications from different services/caracteristics. For now I have two services, one for the battery and one...
Hello, i have a strange situation here with TWI module and i have no idea what is happening. I have read a lot of posts here on devzone and the code i am using is also found...
Hi,
I am using nRF51822 spi as a master to communicate with the AFE. Four bytes need to transfer each read or write process. I use nRF51_SDK_10.0.0_dc26b5e.
Configuration...
