Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
For our current application we are using NRF51822, SDK 6.1, Soft device s110 ver 7.1.0.
In our application nRF is configured as SPI Slave and another controller as SPI...
Hi expert,
I am developing 51822 under SDK 6.1, and we have one button and some sensors' interrupt lines as input GPIOs in our platform. In my code, after calling gpiote_init...
Hi there,
I am trying to send six 20 byte packets per connection interval. Is changing the length of charecteristic simply
attr_char_value.init_len = sizeof(uint8_t...
I have set up a board using device_manager_central to connect with BTLE sensors. I have used a combination of the multilink example and the heart rate collector example along...
Hi,
I used nrf51822- EK board.
GATT - s110 6.2.1 softdevice
I transfer data through UART for nrf51822-EK(PCA10001).
But this time. I used nrf51822 smart beacon...
I develop with nRFgo SDK 2.3.0.10040.
Normally PRX can communicate with PTX by auto ACK, but when there are two or more PRXs with same configuration exist, once PTX sends...
Hi all,
I am trying to use for the first time my nRF51822 development kit, following the "Development Kit User Guide v1.3".
The problem is that when I open "nRFgo studio...
Do all revisions of nRF51 have the same 4kB RAM sections with separate RAM AHB slaves? The product specification clearly states that only for revision 3 chips.
Not really a question, but it took me way to long to find out about J-Link RTT (i.e. j-link Real Time Terminal for easy debug printing so I thought I would mention it for...
I need a fixed voltage reference on my circuit. Since nRF51822 has internal 1.2V voltage reference, I am just wondering if there is a way to use this reference for external...
Header for nRF51 (nrf51.h) mentions two peripheral blocks completely missing from chip documentation. Are they functioning? If so, the comment for PATCHADDR field of PU says...
Hi there,
After prototyping a device with modules and on a breadboard, I transitioned to a custom PCB with nRF24L01+, matching network from the spec sheet, and 2.45 GHz...
Hi everyone
now i used softdevice s120 scan and connect two s110 device
and i used sd_ble_gap_rssi_start() when connect event ,
then get the rssi in BLE_GAP_EVT_RSSI_CHANGED...
HI,all!
Recently my nrf51822 device encountered a tough issue,the detials are:
My device connected to an android app, which has some bugs about ble connection so the...
