Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hello,
We are working on an audio project where we are using nRF5340 Audio DK. We want to externally interface the digital microphones without using the on-board codec ...
Hi, We want to integrate LORA LR1110 for the final year capstone project. From the documentation we have understood that Kit is fully compactable with Arduino UNO. But SPI...
안녕하세요
nrf9160DK 보드로 개발하고 있습니다.
blink 예제로 컴파일 및 다운로드되었음을 확인했습니다.
SDK에서 예제AWS_IOT_MQTT로드하여 테스트하고 있지만 아래와 같은 오류가 발생합니다.
해결 방법을 가르쳐 주시면 감사하겠습니다.
zephyr/subsys/net/libsubsys__net...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
I've been testing the littlefs sample on NCS v2.8.0 and v2.9.0 with an external SD card. Initially I tested the sample with an nRF52840-DK and everything worked as expected...
I'm getting the following notice/warning/error when building my application (nrfsdk 2.9.0 w/ sysbuild, nrf9151dk board):
/usr/local/zephyr-sdk-0.17.0/arm-zephyr-eabi/bin...
Using nrfutil/dfu, I have previously flashed an older application+SD (s132_nrf52_3.0.0) onto the nRF52840 dongle.
Now, I cannot flash my newer application, since it contains...
Hi All,
Simply put I am trying to use the Xiao BLE Sense board connected to the Expansion board (with SD card slot) to write audio recorded data from the Xiao embedded PDM...
Hello, I'm programing my project while using the nrf52840 chip. I'm using segger embedded studio for the programming part because with the nrfconnect I have error code 9 ...
Hi I wish to integrate Matter over thread in unicast audio server . My objective is to use matter to control the volume and play/mute states. I would like to know whether...
Hello, checking if it's at all possible to have uart working on the nrf52832-dk using pins 18 and 21. I can get rx/tx working with an ftdi using pin 12 & 13, but not 18 &...
SETUP:
2 x NRF54L15 DK initiator/reflector sample (as of 4/8/2025) Major RTT settings below - RTT (BT_CONN_LE_CS_MAIN_MODE_1) with 1M phy, 32 bit random RTT (will add settings...
I am working with nrf52840 dongle, details on the antistatic cover are( nrf6829, 2.1.1, 2024.02). I am trying to flash it using https://github.com/adafruit/Adafruit_nRF52_Bootloader...
Hi all,
I'm facing a challenge with efficiently transmitting high-frequency sensor data over BLE.
I’m sampling sensor data via SPI from a sensor capable of outputting...
Dear Team,
I am attempting to provision my Thingy91 device to AWS IoT Core using Fleet Provisioning with the Claim method. I've been closely following the instructions in...
Hi everyone,
I'm experiencing an issue with my nRF54L15DK board.
When I build the OpenThread CLI sample with the /ns configuration, everything works as expected. However...
Hello, I am working with a Seeed XIAO nRF52840.
I'm able to get an average of 500 uA in SYSTEM OFF mode. However, for this application, the current consumption during wake...
Hi guys, With v2.8.0 sdk, L4_e3 code ( academy.nordicsemi.com/.../) works with nrf52833dk. We have a custom board that we designed. Here, nrf52820 chip is used. I can compile...