Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
We are finishing up a project with the nRF52832 based on the Nordic Thingy. Most of what we want it to do are normal functions of the Nordic Thingy. It connects to a mobile...
I feel like a crazy person looking to store large amounts of data onto an external chip that is not a micro-SD (why not micro-SD? It's power-hungry and finicky ). NAND through...
Hi
I try to run BLE HRS collector example.
when I run the project, in RTT terminal I have these error
00> sd_ble_enable: app_ram_base should be adjusted to 0x20001CD8...
Google open-sources the firmware needed to build hardware security keys
Google open-sourced today OpenSK, a Rust-based project to aid hardware vendors build hardware security...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Hi I am trying to get an SD card hooked up to my nrf52840 devkit. I am using nRF Connect v2.6.1 and I was trying to get the sample code working, so I used the sample in ncs...
I have downloaded nRF connect setup V5.1.0 and nRF command line tools V10.24.2.
downloaded nRF connect extension , SDK pack and tool chain in VS code.
I added the build...
in this example:
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/conn_time_sync/README.html
the peripheral has this assert statement when...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
Hi
Is it possible and what is the correct way to implement main clock trimming at runtime? Which NCS version this works on?
I see there is already some setup going on...
Hi,
I want to write data to a specific memory. I understand there is ZMS.
https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/subsys/fs/zms/README.html#zms...
Hi,
I am trying to build memfault sample as in intermediate course, after hello_world project configuration and prj.conf options addition, i get following build error...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Setup: NCS v2.8.0 nRF52840
Hi,
I would like to ask about the implementation of Zephyr's SAADC driver (` adc_nrfx_saadc.c `).
In the project I'm working on, I need to...
To read the MAC addresses defined I use the following code (with CONFIG_BT_ID_MAX =2 in prj.conf):: :
bt_addr_le_t addr [ CONFIG_BT_ID_MAX ]; //space for random address...
Hello everyone,
I have an nRF5340 microcontroller (NORA B106 module), and I want to connect a square wave signal to one of its pins to read its frequency or count the number...
Dear Nordic:
I used V2.8.0 SDK to build light bulb, and I have commissioned bulb A(node id: 11) and bulb B (node id: 11) successfully!
Then I used below command to add...
Hi,Team,
I'm using the nrf54l15-dk to develop zms to save custom configurations without affecting the pairing information of ble.
So I have a few questions: 1.Is the storage_partition...
I am trying to set up FOTA support with external flash for mcuboot secondary partition. I have gone through several tickets on the subject, but haven't been able to solve...
