hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I try to compile SDK example following the tutorials ( devzone.nordicsemi.com/.../) ,
but i got some problems.
1.I can't finish setp of " Setting up a project for debugging...
Hello,
We are working on android UART service and NUS characteristic to receive notification and testing with the custom board with S130 stack acting as a peripheral.
...
Timer_interrupt.txt
Hi all, can anyone please help me in setup up the timer interrupt? I could only see the printing of "Entered 2". Kindly check on the attached text file...
Hi,
I developed a wire-less sensor based on 51822-BLE. I need a batch test method for the product.
My thought about the test is that connect the sensor to phones, and...
Hi support team,
I would like to know if the following behavior is a normal behavior:
My config: NRF51422 AAE0 + S310 V2.0
When I enable some inetrrupt like UART for...
I went through the documentation of nRF51-iOT-SDK v0.8.0 step by step. But
I could not cross-compile and build the kernel with 6LoWPAN on MAC OSX. I do not have a Windows...
I'm updating our bluetooth firmware and boot loader over the air from iOS and android devices. I've modified the nordic supplied update code (IOS-nRF-Toolbox project) to support...
I would like to use functions from components/libraries/mem_manager/mem_manager.c but it doesn't compile because of absense of sdk_config.h header file.
/home/gerbsh/sdk_11...
I'm concentrating on a work about connecting nrf51-dk device in the sensor node end implementing COAP server, ble enabled rapsberrypi and COAP client using Copper.
To check...
The PPI has been configured to transmit a message every time the timer triggers ( every 1ms).
I'm using IAR Embedded Workbench 7.40.3.8938 as my IDE .
When the system...
Hello all,
Our product based on nRF51 is on preproduction stage. We use both 16MHz and 32kHz external crystals.
The question is:
Is there any way to check programatically...
Dear all,
I do have troubles with the bandwidth of the nRF51822 contained in the Adafruit's Bluefruit LE SPI Friend module. The max. throughput I get is 213 B/s. I'm using...
After doing some DFU work - and it all went fine and dandy ...
I would like to go back to the plain old default bootloader that came with my nRF51 board. I don't seen any...
I'm using IAR IDE for the nordic development of NRF51822 (mdbt40). I'm able to run the example project which does not required soft device. Now i wanted to move further with...
Hi,
Is it possible to program the nRF51-Dongle through the usb, to correspond to Bluetooth content to change GPIO state. Then connect the dongle to an external power source...
