I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up to read the potentiometer's raw value . As part...
Hello, I have been going through the DFU and FOTA lesson in the Nordic intermediate course. I see that there is a FOTA support for a scenario in which we want to update a...
Does anyone know of a good tool(s) for prototyping proprietary services and characteristics for App development? Our App dev team is ahaead of our firmware team and they want...
Hi,
I'd like to know how tp estimate of the best "timing accuracy" I could expect to achieve between an iOS device and a peripheral device. The objective is to make a specific...
Hi,
In my application I want to communicate nRF24L01+ with nRF51822 with dynamic length. Some settings are:
In nRF24L01+ side (reference: devzone.nordicsemi.com/.../)...
Hi,
Now I use these fun in ANT SD210 like below:
void MyFlashWrite(ble_ant_csc_t* cscdata)
{
uint32_t addr;
uint32_t patwr[3];
uint32_t pg_size;
uint32_t pg_num;...
what information does the nrfjprog.exe write to UICR(User Information Configuration Registers) register??
==========Tutorial of Flashing dfu bootloader to the nRF51 DK...
I want to use the ble sniffer to capture two peripherals connected to the master control panel.
with the ble sniffer I can only select one peripheral for capturing packets...
Hey there, I've posted this issue on the tutorial website and I came across a post stating that posting here will get me a quicker response. Here's my problem, when I tried...
In my application need to nrf8001 connect(bond) to e phone in a specific duration (for example 1 hours )and then disconnect and in one hour later bond again. In this duration...
Hi,
I am developing a Heart Rate application.
I need to ensure that i am flashing correct softdevice file through my application.
How can i do that?
Regards,
Sum...
Hi,all
i study DFU step by step according this link devzone.nordicsemi.com/.../a00076.html,but failed at step 8.my peripheral advertising as Nordic_HRM not dfuTag.
Can someone...
hi,
I used previously nrfjprog version 5 to program SD+APP+BL with --dfu flag and I can perform OTA DFU.
Now with version 7 there is no --dfu flag anymore and if I try...
Same question as devzone.nordicsemi.com/.../
What needs to change for a gcc setup in the compile flags.
If that helps, some of the flags I have now include:
-mfloat...
Hi,
I'm using s130 and my mcu is both central/peripheral. In the centrol role, when I try to connect and pair with an peripheral, I get all the way through SMP pairing...
I have been developing an application using PCA10028 board which needs to use timer. From the SDK8.0.0 pack, I found an example "timer_pca10028". It works fine when the SD...
