Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
hello,
I recently purchased a NRF51 dongle and NRF51 DK. I was working with older version of NRF51 development kit. I did n't get any information in the user guide provided...
Hello,
when using the S130 with multiple connections and sporadic advertisement and scan procedures, I get a connection timeout after a few minutes, now I must know, how...
Hi,
Im using an app_timer in my application to create a timeout for UART read (im not using SoftDevice).
On my board I have USB and battery power, so at the moment when...
After switching to 51822 in example project nRF_Examples\7.0.1\dfu\bootloader\
I have next output:
compiling pstorage.c... compiling bootloader.c... compiling bootloader_settings_arm...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Besides the fact it's a later release?
i.e., why does one have "nRF51822" in the name and the other simply "nRF51" ? Is it because the former will only work on a 51822...
Hello,
I have the Bluetooth Smart Beacon Kit along with the Dev kit (J-Link Lite and other eval boards). I am using the nrf51 SDK version 6.1.0.0 in eclipse along with GNU...
I have a a new pca10028 DK board and a pca10000 dongle. Using Keil v5.14 and Nordic SDK v7.2 I can compile, download and test several pack examples (e.g. ble_app_hrs, ble_app_alert_notification...
We need to develop a system that can receive multi heartrate ANT+ strap signal at least 50 to 100m range. Im newbie in this technology and I don't know if is there any antenna...
Hi
I am using SDK8.0.0 ble peripheral sample code and PCA10001 board but I am not getting any advertise ment on sniffer.
I have test hrm, template and ble nus_uart code...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hello, I build a BLE 6LoWPAN environment on my raspberry pi with Kernel 3.18.3 and connect a BLE Dongle. The BLE Node is Arch BLE ( www.seeedstudio.com/.../Arch-BLE-p-1998...
I referenced the question in this link devzone.nordicsemi.com/.../sd_ble_gattc_primary_services_discover .
And I can see the Read by Group Type Request and response in sniffer...
