How can I display the nrf serial terminal logs files on VS Code while keeping the same colors and text highlights for dbg , inf , wrn , etc., just like when viewing live logs...
Hi,
I am trying to build bluetooth hci_uart sample for esp32 board and haven't had much success so far. I am running this command to build:
`west build -p always -b...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Hi,
If the following function is used, how to solve this error:
#include <nrfx_reset_reason.h>
void check_and_clear_reset_reason ( void )
{
// 获取复位原因
uint32_t...
2025-06-13T08:43:42.649Z INFO Initialising the bundled nrfutil device 2025-06-13T08:43:42.652Z DEBUG Started watching devices 2025-06-13T08:43:44.400Z INFO Using the bundled...
I want to confirm with Nordic staff that the MBR compares the new bootloader with the one it will replace when executing SD_MBR_COMMAND_COPY_BL. It seems that after a comparison...
Hello
Just few quick questions. What happens to the S110 Softdevice after the APP_ADV_TIMEOUT_IN_SECONDS period?
I'm using the nRF51 DK and the ble UART example and I...
As I am using nRF51422 EK (Evaluation kit), would like to know how to test with BT2.5 or lower version. Is this has backward compatibility. As when I give option of FLAG other...
Hello
I'm having difficulty in executing an GPIOTE interrupt during a BLE connection event with the nRF51 DK. The interrupt I have works fine when the softdevice is advertising...
If I set the centrals connection intervals values higher as a specific value it won't any longer find/connect/enable notifications on my peripheral.
0x00A0/0x0050/ 400...
After running the advertising_start () function in the sample software.
I set the breakpoint by Keil MDK-ARM v5 and stopped executing.
Afterwards, reset is generated!!
...
Hi,
I am using a gpiote interrupte handle function to send a notification to the master,but I find when the sd_ble_gatts_hvx() function is used,the interrupte handle function...
I have successfully completed dfu using android app, but if anyone can help me with example program so that i can perform dfu using program instead of using toolbox app, please...
On the XLR2 chipset I am seeing that if the RTS output follows the state of the CTS input.
When I load the same firmware in a XLR then RTS does not follow CTS
Hi, I am evaluating the use of ESB(without Ack) and BLE as a possible solution for my project since i have no use of Ack and in Gazell it is mandatory to use Ack. I had heard...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hello,
I'm drawing schematic with nRF51822 internal LDO. I'm wondering what is the regulated LDO output from nRF51822. I need to connect that with peripherals in stable...
We are using ANT with the nRFgo motherboard as base station and want to broadcast a signal over the largest range possible (> 100 m) to several mobile devices using the Dynastream...
I am designing a ECG monitor device. The data rate is less than 50kbps. I was planning to use BLE for the device design. But I read some documents that say BT classic is a...
