HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi All,
I use S120 device to monitor advertising and output the mac address,RSSI information via UART to PC terminal. The PC terminal can receive data continusly from the...
I found ble_dfu.py referenced in some posts to help automate the generation of an application.dat metadata file used (along with the application.hex file) to create the input...
in the code below, the keil IDE is flagging with red squiggly APP_BUTTON_INIT, claiming that it is an undefined symbol. It also says that this implicit declaration of 'APP_BUTTON_INIT...
Hello all.
while trying to calculate the data rate from bluetooth low energy , i have two questions
Is there a possibility to measure the data rate by using nrf sniffer...
I have an algorithm which does quite a bit of number crunching. I'd like to know how many clock or instruction cycles this algorithm is using. How can I get or calculate the...
Hi all,
I am not sure what to do now. I have been trying to get the s130 working with the device manager. I tried using github.com/.../nRF51-ble-app-hrs-s130 with sdks...
Hello,
in my application i use a bootloader for S310 and S310 V2.1.0.
The Bootloader is configured to use NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION and the application...
Hello Everyone
I am using two application timers one of standard battery service and one i have made for adc sampling like this along with the code added for battery timers...
When I update the advertising data from the radio pre activation hook (800µs), the updated data does not appear in the advertising event following 800 µs after the hook is...
Custom Board with MCU NordicSemi nRF51822-QFAA
Softdevice S110 7.1
IAR for ARM 7.1
SDK 7.2 using a merged service (HID keyboard example + NUS example...
As per the steps given to program bootloader to the device i have programed it.
But the code is not getting executed i.e advertising nor led initilization is taking place...
Hello im trying to connect to a slave on BLE_GAP_EVT_DISCONNECTED event.
Can i use sd_ble_gap_connect(...) on this state, im getting error code 0x3202.?
regards, Vo...
Hi, I have bought the nRF51 development kit. I have downloaded source code for nRF51822. This comes with LOTS of examples but I suspect the codes are not for my board. Is...
I'm manually creating the .dat file for a DFU following the format specified in this document .
Where can I get the device type and revision values from to populate those...
I have bought the nRF51 dev kit. I can download all these soft devices. But what do they really correspond to ?
I think of them as library/apis for doing BLE development...
