I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
I am using nRF Cloud to update firmware on nRF9160 based products in the field. They are connected via LTE Cat-M on Telstra in Australia. The problem is that the download...
I need help with this issue. I'm updating the code from SDK 2.4.2 to SDK 2.9.2. I had change the device tree to HWM2 and I'm using sysbuild.
The build log is showing this...
Hi all,
I'm trying to set up MCUMGR on 54L15, such that it can receive images from my border router when they're in the same Thread network. I read that we can upload images...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
Hello, I'm developing on an application which requires to catch high speed, variable size and bursty (~0.5 Mbit/s) data from a sensor connected to a nRF9161DK trough a UART...
If I try to compile any of the WIFI examples for the Thingy91x I get a RAM overflow error. The only exception to this is the WIFI scanning example. If I build these for any...
I am trying to scan and connect to a Polar H7 HR belt (which I can do), with m_scan_mode = BLE_NO_SCAN. Once this happens, I understand they are supposed to bond, and at that...
In my low-power application I need to use advertising interval of few seconds (two or more) in order to get lifetime of a year with CR2450 battery. However, the Android application...
There's a great application nRF UART 2.0 that can be used like a terminal with a Bluetooth LE device implementing the "Nordic UART" service. Now I would like to store output...
I am using a nrf52832 with SDK 11.0.0 and sd132. I need to add in-flash storage to my application so I'm looking at the NVMEM documentation and the pstorage module. I understand...
Dear Sir/ Madam,
I want your suggestions and recommendation regarding to choose which one of your BLE development kit.
I want a Bluetooth development kit which has long...
Hello, I'm trying to update services list on central device after adding a new service. However, sd_ble_gatts_service_changed returns NRF_ERROR_NOT_SUPPORTED . After looking...
Hello,
In my application, I need to activate BLE during startup only if some conditions are met otherwise I put the nRF52 in SystemOff mode. BLE should not be activated...
Hi,
I have been receiving the error: undeclared identifier "TWI0_USE_EASY_DMA". I researched and found that the solution was to include "nrf_drv_config.h" and add #define...
Hi, I have problem with discover services in advertising mode on NRF51822-BEACON. There is default firmware in this beacon. I using Xamarin on Visual Studio 2015. It is connected...
I have integrated IAR code into my company system.
with the Jlink_monitor.c, jlink_monitor.h , jlink_monitor_ISR_ISR.s and enableMonitorMode.mac.
Step 1: I loaded code...
Hi,
I am trying to use the nrf_drv_twi class but I cannot define a nrf_drv_twi_t instance. When I write the code
`nrf_drv_twi_t twi = NRF_DRV_TWI_INSTANCE(0);
I get...
Hi,
It is indicated on page 59 of the datasheet (rev1.0), concerning the register nr.8 OBSERVE_TX, that "the counter PLOS_CNT is reset by writing to RF_CH . See page 75...
I am working with SDK12.2.0. I see that transports seem to be registered as section variables with the identifier dfu_trans
I have added a section definition in flash to...
Not sure if this is a typo in the function comments or a small bug, but thought you'd probably want to address it either way. I'm on the most recent NRF5-SDK (12.2.0) and...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...