Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hi,
I have a question regarding the NRF 52 boot sequence.
When we first receive it from Nordic, what are the boot options? Are there any other options to load a code on...
Hi,
I'd like to know how to set/alter passcode when pairing happens. I looked a few examples in Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Examples\8.0.0\ble_peripheral but...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hi all,
If i have connect a band with my phone, then i let my band close to my notebook and let my notebook unlock.
Any suggestion about this?
Thanks in advance
Hello all,
I am working on the implementation of DFU OTA in our application, running on a custom board using the nRF51822-QFAC.
The tools that I am using are:
...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
[Update 8/15]
Here's the file for the main part of my code: sensors.c . The sensors_start() function at the bottom is where the while loop and the print statements are located...
I want to send data to my android phone from Nrf51822.My compiler is mbed I use redbearlab NRF51822 kit.For example,I want to see on my phone "hello world".
Mbed Program...
Hi,
I'm using S130 v1.0 softdevice and bootloader (single bank) from SDK v9.0.
When updating an application, I always get a CRC error at end of the upload. I generate...
Hi All,
I want to club both application into single without affecting functionality of each.
basically i want to make ble_hid_mouse example to be pair with my phone...
Hi,
I have got a PCA10001 board version 2.2.0 (2014.10). Now, I am looking for a "step by step" guide abou launching mbed on this board? Please, help me.
Regards,
Pave...
In the Master Control Panel on Android, I have a beacon that is advertising with the BLE flags set to 0x06, which is BREDR_NOT_SUPPORTED | LE_GENERAL_DISCOVERABLE. Its packet...
Hello,
I'm new to nRF51 and would like to understand if it is possible to output 5 independent PWM signals to 5 GPIO pins simultaneously on a nRF51?
Thank you.
