As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Dear Nordic support team,
Could you give some rough estimates for availability of production-ready version of the S130 soft device?
Thank you and with best regards,...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
Hi,
Have some nRF51822-beacon's rev 1.1 that would fit perfect for some tests and proof of concept with an ANT application.
As I understand the 51422 and 51822 are the...
Hi all,
Could you recommend a way of connecting the nRF51422 with PC or laptop running Win7?
It seems that there is no BLE stack for Win7 and thus can't connect. I am...
I am making some NRF51822-based temperature sensor nodes, powered by CR2032 coin cells, and I would like to minimise power usage in order to maximise battery life. I am using...
Hi,
I am doing a BLE based project using NRF51822. I am asked to build a 2 layer board.
According to the reference schematic BALF-NRF01D3 has been used with WLCSP package...
Hi,
I'm close to finishing the implementation of a system with a recording device with nrf51822, working with 6 sensors with nrf24L01.
The recorder is in receiving mode...
I'm looking for an approach to RF coexistence between an nRF51822 bluetooth SOC and a WiFi module such as the WL1801. Does anyone have any experience or recommendations for...
Hi guys,
I tried to flash the pca10001\blinky_example onto a nRF51822 with nRFgo Studio.
Flashing the s110 worked fine. But when I try to flash the hex from the example...
Hello All,
I'm thinking a small plastic case for a portable device.
It is possible to place pcb board (with pcb antenna) above the battery (Li-Po) or can interfere with...
I want to log basic intermittent events and push them to a previously associated mobile device when one is nearby. The mobile device can then forward the events up to a server...
I'd like to know what is the minimum and maximum frequency I can generate on a GPIO with a 50% duty cycle (+/-10% at the worst case). Which resources should I use for that...
In my case active CE signal defines byte boundaries - for each byte individually.
From what I see, DMA seems to stop on rising edge of CS regardless what is declared in...
Hello everyone,
I'm using nRF51822 development kit to do BLE network experiment.
The boards I use are PCA10005 with omnidirectional antenna, and PCA10004 with PCB antenna...
