Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hey there,
I am looking for the right pin out to wire up a reset button to my board so that I can reset the IOS device is paired to. Can some one help?
Tyler
Hi,
Is it possible to set an address lets say for an array to be in Flash memory on compilation?
So that way I dont need to reserve memory twice - once in my program memory...
I have two nrf51822 devices with sniffer firmware. At the beginning all tests were well, it can sniffs beacon packets with ble-sniffer_win_1.0.1_1111_Sniffer and display packets...
[edit]
This problem is solved!
The problem is from project target.
I am using uvision5, but I opened the uvision4 project. (\arm4...)
Now I am using the example under...
I am using the Sys Events to monitor the POFWARN but it appear that I get a POFWARN event repeatedly when the voltage is below the threshold is this normal or do I need to...
Hello,
Some questions regarding the linker script for the 8.1 SDK for SD110.
I was able to get an environment set up with ARM GCC, Make, etc. and compiled my program...
I have a program running with SD 7.2 and SPI on my nrF51822 talking to a SPI slave device. I use GPIOTE triggered on an edge to set a chip select line and read bytes from...
I have a LED dimming project that uses nRF51822 and nrf_pwm_noglitch. If I turn to 100% duty cycle, then it will be stuck at 100% unless I turn it to 0%.
So in other words...
The board is simply an nrf51822 with a crystal and required caps and resistors, without any LEDs. When I try to flash any firmware, I get an OK that the firmware has been...
Hello guys,
I am working on the project where I am making a network4 nrf24l01 transceivers, such that one can broadcast the text message from one transceiver at the base...
Hi, I'm trying to write a long byte array with the nrf master control panel on android. I'm unsure if the app is able to, but in any case I'm not getting the event: BLE_EVT_USER_MEM_REQUEST...
Hi,
I have my custom nRF51822 board, and i used to flash the firmware through nRF51 DK kit.
As there are two ports through which we can load external boards i was using...
Hi,
I'm trying to build a prototype using the Adafruit nRF8001 Breakout and an mbed ARM CPU.
After Reset, I get a Device Started Event, telling me the chip is in Setup...
