Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi all,
I'm using the nRF51822-EK (PCA10001) and I'm going to develop a bluetooth cadence (and speed) sensor for MTBs.
I desire low power consumption and i though to put...
hiii...
I was working on ble_app_hrs example of sdk-6 using sd7.0.0. I tried to add broadcast feature by sending some hex values, dat was working, but now i want to display...
Hi,
I need to use 2 TWI bus (hardware constraint) so I wish to drive one bus with twi_hw_master.c and an other with twi_sw_master.c.
Each bus have their own GPIO.
...
Hello.
I'm reading the nrf51 Reference Manual.
in MPU section, [ (SWD) will no longer have access to code region 0 or code region 1, as well as no longer being able to...
Hello,
downloading the file nrfgo_sdk_2.3.0_setup.exe causes the virus scanner to report an issue and moving the file into a restricted zone.
Can you help on this...
hi, i made ble app with nRF51822 (s110), sdk 6.1.0
and i put this code after a pstorage_store() function to wait finishing of this function.
uint32_t err_code, count;...
My board is nrf51822.
Simple_uart works fine in uart_example, but once I copy it to my ble project which can work, it stuck.
Part of my code :
advertising_init();
services_init...
Hi all,
Now I'm using the nRF51822 DK and nRF Loader APP do the OTA.I can use the APP to complete the firmware update.However,the device
cann't go back to bootloader mode...
I'm trying to build an application on nrf51422 with s310 SDK ver5.2. My application is working fine with Bluetooth and now I want to add ANT service to it so can anyone please...
We are running OTA DFU bootloader provided in SDK 6.0 on nrf51822. We noticed that when the chip has been on for a while and we quickly power cycle it, the bootloader sometimes...
Thank you for your reply,Nikita
description of my system: Hardware:nrf51822,pca10001 Software:sdk5.20,run the softdevice s120
According to your reminder.i reference...
Hi,
We need to simulate the peripheral through PC, but with current version we cannot use 128-bit UUID which we need.
So the question is are there any plans to release...
Hi,
I want to init all 8 pipes in the host device (gazell protocoll) with a single init byte.
Thats important because i want to send that init byte to the devices with...
Hello,
as I know max number of simultaneous connections for s120 equals to 8. Is it software or hardware limitation?
Is there 'serialization' version of s120 (worked using...
Hi,
I use a step-down converter(not the integrated one) to generate 1,85V for the nRF51822 in my application.
When the applications starts the output voltage from the...
