I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hello Nordic Support Team,
I’m developing a Zigbee-based light switch using a Sleepy End Device (SED) configuration with ZBOSS. I've encountered a critical issue related...
I'm facing a persistent issue with my nRF9151-SMA-DK kit when trying to perform USB debugging, uploading, recovering, or erasing.
Interestingly, other boards (nRF9151-SMA...
Where can I obtain the security certificates (e.g., client certificate/private key) needed for TLS authentication with nRF Cloud? - Are these generated during device onboarding...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hi, I'm working on a project and I need the GPIOs to have 3.3V available when the nRF52840 is in deep sleep, in order to use wake-up on GPIO. So I'd like to know what the...
Happens consistently and in production.
The stream advertisement is still there but cannot be connected to by any receiver (both 3rd party and our own). 3rd party says connected...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
normally, I would set the CMAKE_BUILD_TYPE to `Debug` to enable Cs "assert" function (not define NDEBUG). Zephyr (and Nordic-Zephyr as well) has the `CONFIG_ASSERT`...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
안녕하세요
nrf9160DK 보드로 개발하고 있습니다.
blink 예제로 컴파일 및 다운로드되었음을 확인했습니다.
SDK에서 예제AWS_IOT_MQTT로드하여 테스트하고 있지만 아래와 같은 오류가 발생합니다.
해결 방법을 가르쳐 주시면 감사하겠습니다.
zephyr/subsys/net/libsubsys__net...
