Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello,
I have this problem when I try to generate the key: Key generation failed: -134
Here is the prj.conf file:
CONFIG_BUILD_WITH_TFM =y
# CONFIG_TFM_PROFILE_TYPE_MINIMAL...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
1st issue: Tingy91X doesnt build at all with debug -Og enabled: Because of all the strange issues of Thingy91 (nRF9151) and "not to be used in new products) we ordered a couple...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
I just want to double check something before I optimise an implementation.
If burst is enabled on multiple channels, let's say x256 for two channels, internally is the process...
I use nrf5340 DK as AP, nrf54l15 DK as TAG.
Below was uart print comments from AP
ESL_AP:~$ > esl_c bond_dump
esl_c bond_dump
Dump bonded device
ESL_AP:~$ > esl_c...
Hi All,
I am currently evaluating how I can charge a single cell with the nPM1300 PMIC with a USB-C connector, with the addition that the same USB-C connector should be...
Hello Nordic Support Team,
I’m developing a Zigbee-based light switch using a Sleepy End Device (SED) configuration with ZBOSS. I've encountered a critical issue related...
I'm facing a persistent issue with my nRF9151-SMA-DK kit when trying to perform USB debugging, uploading, recovering, or erasing.
Interestingly, other boards (nRF9151-SMA...
Where can I obtain the security certificates (e.g., client certificate/private key) needed for TLS authentication with nRF Cloud? - Are these generated during device onboarding...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
Hi, I'm working on a project and I need the GPIOs to have 3.3V available when the nRF52840 is in deep sleep, in order to use wake-up on GPIO. So I'd like to know what the...
Happens consistently and in production.
The stream advertisement is still there but cannot be connected to by any receiver (both 3rd party and our own). 3rd party says connected...
