Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello
I've been experiencing an unusual problem using the TWI/I2C library for the nRF51-DK board. Basically, I found that I need to shift my device address to the left...
Hi guys,
I have followed devzone.nordicsemi.com/.../ to set up CrossWorks. Even though I got pass the ble_stack_init();, I still can't discover the device for some reasons...
Hi
Please tell me someone me how to start nRF51822 & softdevice8.0.0
I build a NRF51822 application in gcc & ECLIPSE.
When to run the program, it crashes in the boot...
I'm having a problem adding the GPIOTE_IRQhandler() to my main.c file (see attached). I'm getting a compiler error that it is doubly defined in app_gpiote.o and main.o, but...
is it possible to update the pca20006 (rev. 1.2.0 2015.06) beacon with the pca10000 over DFU?
When i tried to update it with my application written for an older version ...
Hi folks,
I'm using the ble_app_template on a custom board. The BSP has a bunch of stuff I don't need, so I would prefer to not use it and handle my I/O directly instead...
i was going through TWI initialization process here i am confused why have we disabled Blocking mode. The reason for Disabling TWI_BlOCKING_DISABLED
I am referring the below...
hi , i want to modify the "transmitter_pca10028" and "receiver_pca10028" examples in SDK to obtain a transmitter/receiver in the same time (tranceiver). So someone have idea...
Hello, I am using the nrf51822EK and I want to combine the ADC and LPCOMP although in the reference manual it says they can not be used at the same time. Is it possible to...
Hi all,
I met one strange thing on SPI interrupt:
when 51822 advertising, the SPI write and read works well;
But, when CONNECTED, with BLE_GAP_EVT_CONNECTED event occured...
Hello,
I migrated my project from softdevice S110 7.1.0 on a nRF51422 FAC to softdevice S110 8.0.0 and an nRF51822 FAA G3. My code used to have a current consumption around...
Hello everyone,
I'm currently using and modifying the experimental_ble_app_uart. I've seen that for sending characters resp commands the file simple_get_uart is used. My...
Good morning.
I'm curently trying to set up an exemple project in Eclipse, but I've tried sevrals tutorials unsuccessfully. Somes are out of date, somes gives me errors...
