nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Nordic,
I am using the BLE Shield v2 and the Arduino Due board to transmit accelerometer/gyro data to an Android tablet app that plots this data. I had this working fine...
First I noticed that nordic has already updated the andriod nrf toolbox app to use softdevice v7, which allows updating the softdevice, bootloader and application.
The...
Hello all,
I'm working on a library for NRF24L01+ and PIC micro.
Unfortunately there is something wrong. On the receiver side, the micro correctly detects that a packet...
Hi,
I am knew to BLE and I was able to ran succesfully the blinky project. Now when I load the soft device on and then try to download the hr example if says "Flash download...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
Hi,
I develop an application with the nRF51822 circuit. It is detectable with my smartphone, but not with a computer that has a Bluetooth 2.1 device. Is it possible to...
In the comment of this post , Marc Nicholas wrote:
Doesn't that require SWO to be implemented? (Which is not on the Nordic part).
Is it true, that SWO isn't available...
In SDK 6.0 I find there is a project of ble_app_hids_keyboard_serialization.uvproj in nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
and it contain...
Hey there,
today I'd tested around with the Dfu service.
Peripheral is nRF51822 running Sdk 5.2.0 bootloader example (Softdevice 6)
Central is Android 4.3 running...
I am unclear whether the soft radio takes care of updating the attribute when a write event occurs. I can see in the example codes that the notification flag is handled by...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm trying to understand how pstorage allocates storage.
PSTORAGE_FLASH_PAGE_SIZE is fixed, that's the actual size of a flash page and thus a basic unit as you can only...
Hi, I am trying to change the beacon data.
I changed Beacon UUID already, but I can not find where can I change device name.
I guess I need to change the gap_adv_data...
Hi,
I am upgrading to SDK 6.0.
What function should I use for retriving the whitelist data?
SDK 5.2:
//err_code = ble_bondmngr_whitelist_get(&whitelist);
//APP_ERROR_CHECK...
