Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi All,
We am trying to check and interface Nordic's EMK with custom board running android kitkat.
Problem is we cannot access internet/play store from custom board...
Hi,
I'm using nRF51 BLE driver on PC to simulate BLE peripheral using PCA10000 v2.2 dongle.
I need to add some functionality to the default connectivity app. So I compiled...
Hi, and thanks for reading this.
I attached additional LED to nRF51822 p0.24
however I can not find how to handle it .
if I want to use this function
nrf_gpio_pin_set...
Hey.
Hope this was not asked before. At least I did not find it.
I'm trying the ble_app_hrs_c on s120. Got it to build with gcc (d'oh) and got the serial logging to...
I want to make a robot that can track the direction of the transmitter that is controlling it, for example to aim a camera at the transmitter. The robot vehicle will be controlled...
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi!
Maybe I'm doing something wrong (very possible), but for example, when I want to store array of 3 uint8_t values I use:
uint8_t dataToStore[3];
dataToStore[0] ...
Device: nRF51822 Rev G0
SDK: v5.2.0
Code: raw.githubusercontent.com/.../twi_hw_master.c
Basically, the TWI driver which uses PPI channels (sd_ppi_*) works perfectly...
Hello,
I am using a nrf51422 development kit with softdevice S310 and I have a problem in whatever pin I choose as output when I use the bluetooth.
I run the example...
I tried code like
static void on_ble_evt(ble_evt_t * p_ble_evt)
{
....
case BLE_GAP_EVT_TIMEOUT:
if (p_ble_evt->evt.gap_evt.params.timeout.src == BLE_GAP_TIMEOUT_SRC_ADVERTISEMENT...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am unable to compile this to fit into the allocated bootloader space.
Has anyone been able to compile this patched version of the signlebankdfu-ble
with nrf sdk v6 so...
I'm using API 2.1.3, and after several connections/disconnections with a peer device, I'm seeing the API never returning from a DiscoverPipes() call. It appears to be waiting...
