I have a project that I need to use most of the GPIO pins available on the nRF52840 DK. I'm using SDK V17.
I'm writing a test program that toggles all GPIO pins on an nRF52840...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi,
I see that you provide Master emulator API for windows (dll) that works with firmware for Master control panel application. Master control panel firmware, as the name...
Hello,
I try to set up an external signal for the LFCLK on a nrf52832. From this question :
I know the nrf52832 can do this (signal on XL1 pin, XL2 grounded).
...
Hello,
I am working on development to concurrent multiprotocol: BLE+2.4G proprietary. I am using timeslot feature in S132.
Because in my own 2.4g proprietary protocol, the...
I want to use feature reports in my HID project, but as far as I see this functionality is not fully included in ble_hids.c (SDK 11). I already managed to properly receive...
Hi,
I want to advertise in variable intervals and mostly only one advertisement at a time. I planned to do it like this:
1- start advertising with any interval (e.g...
Hello,
I followed the example for doing 128 bit UUID advertising using ble_app_uart example. The problem is, this seems to work if I run it when the radio and controller...
Hi,
I have my custom nRF51822 board based on Raytac MDBT40-P module. I am trying to program it with nRF51-DK(PCA10028). I could program it with mbed interface once or twice...
Hi,
I want to implement Advertising with the Timeslot API. I only need non-connectable advertisements but I want to be able to control the transmit power.
Which example...
Hello all,
I would like to understand advertisement packet more.
if I add the following to my packet my firmware causes nrf51822 to crash.
advdata.include_appearance...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I'm using the BMD-200-EVAL S board (using Segger JLink). I've defined SCL and SDA as:
#define ARDUINO_SCL_PIN 5
#define ARDUINO_SDA_PIN 8
When debugging into the...
As title, where can I find the syntax for this editor?
If it does not exist,
Q1. How can I put sample source code block?
Q2. How can I put new line only? (without...
Hi,
What's the maximum current for nRF52832 when only CPU is running from RAM at 64MHz (DCDC 3V condition)?
From Product specification v1.0 page 18, does the value "3...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
