Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
Hi all,
I just received my nRF52 DK and started attempting to run examples on it. I am having an odd trouble that the LED2 is always lit after programming the board, no...
Hello,
I ran PCA10005 board with nrf51-ble-app-lbs application and programmed PCA10004 with S120 ble_app_multilink_central. I have connection between them (I just changed...
Hello everybody,
I am currently experimenting with BLE on the nRF51-Ek. At measurement on the oscilloscope, the BLE protocol shows a behavior that I do not quite understand...
Hello.
I get error 0x10 (error for invalid flags) when i want to write to peripheral with my master module. I use the same code i always used, and i didnt change anything...
Hello.
I written code for nRF51822 w/ MPU6050 in S110(8.0.0) and Keil.
I tried to setup gyro as bellow.
twi_master_init(); => mpu6050_init(MOTION_SENSOR_ADDRESS);...
Hello
I have connected the nrF51-DK board and it was recognized by the computer.
I have managed to put in in a boot loader mode.
Since I switched it to boot loader...
I have three pca10001 boards. One is programmed as multilink central and other is programmed as multilink peripheral. when both peripherals are connected to central, the central...
I'm a newbie for Nordic development.
I just noticed that softdevice, app, and bootloader share the same CPU, RAM and Flash at the same time. This three software modules...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
Hi
I use an avr attiny441 with the nRF24AP2. Communication is over SPI byte flow. After start up, I get the start-up-message from nRF24AP2. That's fine. Afterwards, when...
Hi
the PWM frequency should reach 8MHz( duty cycle is 0.5 )when use timer0(16M) without SD.but i revised timer demo code from peripheral and only get 50KHz.i don't know...
Hi everyone,
I've found a few posts and a lot of info but I'd like to know if there is an existing example that merges a few of the examples found here ( github.com/.....
Hello.
I want to retain the value of a certain variable after issuing a system reset (sd_nvic_SystemReset).
Can this be done without storing it in the flash memory?
...
Hello.
I use SDK 8.0.0 and PCA10028 board. I try connect board to the Windows 8.1 PC ( i have Tablet PC and Desktop PC with BLE dongle). For connect board to Windows i...
