Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
I have a dual mode BLE / ANT+ nRF51422 design going through regulatory testing for FCC / EU marketing approval. I have previously successfully tested a very similar design...
The spec of nrf52 mentiones 'Propriatary RF' as option. I was wondering if that could be used to implement 802.15.4 which would save us an entire IC and power and like basically...
Hi there!
I would like to implement the nRF24L01-module to one project.
But, it would be great, too, if i can use the application manual to use only the chip itself with...
I have the nRF51-DK development kit (PCA 10028). I'm following the gcc tutorial here - devzone.nordicsemi.com/.../.
I'm using the ble_apps_hrs project as a basis for my...
Is it possible to connect DCC / DEC4 to a transistor to turn on / off a part in my circuit? I assume yes, but I just want to make sure.
Or, is there another way to turn...
Hi again,
If I use BluetoothGATTSetCharacteristicValue and set wr_auth = 1 in the ble characteristics, I receive a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event. I can also see...
Dear Nordic developers,
Does TWI supports bit level clock stretching? Means that after each bit (not byte) slave can hold down the clock and master should perform appropriate...
So I have the following bootloader code:
int main() {
uint32_t code;
sd_mbr_command_t mbr_command = { SD_MBR_COMMAND_INIT_SD, };
code = sd_mbr_command(&mbr_command...
My ANT BLE application runs on a custom board with a nRF51422, SD 310 rev 2.0.0
I can use the nRF UART app on an android phone, but on an iPhone with iOS 8.4 I can't even...
Hello,
I'm using an PTR5188 development board for my project which breaks out PIN 26 & 27 for ADC only. I'm using mbed as my development platform and haven't been able to...
Hi there
Can you clarify a point for me?
Quoting from Gazell link layer user guide:
"If only the ACK packet sent from the Host to the Device is lost, but both the initial...
Hello.
Reading the documentation of pstorage_load and the actual implementation has left me with confusion.
The documentation states that the size and offset parameters...
I uses S110 V6.00 softdeivce ,v5.20 SDK, and the nrf51822QFAC chip.
now I use the 32k ram ,but it is wrong.The program is not run.
I only use the 16k ram ,as same as nrf51822QFAA...
Hello everybody,
I'm trying to make TIMER1 working on nRF51822 together with softdevice.
In particular I would like to drive an interrupt line that goes to another microcontroller...
Let me ask you a communication sequence between nRF51822 and peripherals.We assume 5 peripherals.
In a sample program for multilink, original sequence is that 5 times repetition...
