Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
If BLE device is sleeping,is link layer connection terminated or the link layer connection is still valid..?
if it is valid..how the master will know about the sleeping periods...
Hi all.
Consumption current increases by about 1.5 mA after a battery check.
uint8_t battery_start(void)
{
// Configure ADC
NRF_ADC->INTENSET = ADC_INTENSET_END_Msk;...
Hi all!
My project is depend on the "ble_app_template",which uses the "scheld structure", I am able to read the data from app but not able to send my data with notification...
I have a question about that code, when I test my code with lightblue, it showed me that there is an service called application notification client service, but it didn't...
I'm using GPIOTE library to check the change of two switch inputs.
Normally it works well, but rarely GPIOTE_IRQHandler become never happen even if the pin level changes...
Hi Nordics!
I am using app_pwm.c file in SDK 8.1, and when I use it with softdevice(advertising or data transfer event), sometimes pwm signal is reversed.
I guess, reversed...
Hi Guys,
I am using a the 350Mhz Analog Oscilloscope HM303-6 www.hameg.com/hm303-6.0.html to measure the voltage utilised by the board when it is transmitting data.
...
Hi,
Once I enter into BLE mode I am not able to read any gpios(nrf_gpio_pin_read) also I am not able to set any gpios (nrf_gpio_pin_set).
Below is my example
uint8_t...
I'm trying to establish a bond in my project and then perform service discovery, however the discovery is returning the BUSY error.
I tried to wait for the events according...
In SDK 8.0 the bare word asm was re-introduced in nrf_delay.h , causing failures in compilations that use strict C/C++ standard conformance flags. This was noted in earlier...
Hello Developers
I have to solve a problem for which I could not find much information about online, so I am hoping you guys can help me.
I am developing a WIN32 application...
Hello, For some reason the Ble App Uart is not working on my PC anymore. I have gone over Nordic tutorial again however, the LED doesnt blink and I cant detec the device on...
Hi,
What are the general causes of SDS assert in nrf51/52 ? Assuming that SW has been tested, is there something that could happen in the code that would cause the assertion...
Hi All,
I'm using "scanForPeripheralsWithServices" of iOS to the BLE devices.
"scanForPeripheralsWithServices" sometimes never return anything.
I have to stop scan or...
Hello! I'm trying to build a program for nrf51822 via QT Creator.
I'm using QBS for build. I have a makefile from SDK examples for nrf51822. Someone can help me, how to setup...
