Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Our product is based on nrf51422_CEAA chip with softdevice S110, SDK 8.0.0, dual bank ble bootloader DFU.
We have modified the dfu bootloader example from SDK 8.0.0 to...
I read a document, "Setting up production test using DTM", "nAN-034 Application Note v1.0".
And, Figure 3 shows how to setup test environment.
But, I cannot find which S...
DCDC_testing.zip
Hi,
I am in the process of reducing power consumption in micro esb mode. I use the following code, just for testing. The following code consumes 18mA unlike...
It is possible to load a new firmware in a NRF51822 PCBA using the Nordic Development Kit NRF51DK?
Do I need a special connector?
This is the beacon Module I pretend...
Hello,
I have a board with an RFDuino on it which uses a Nordic nRF51822 internally. We are seeing a few of them auto-brick when the input voltage dips too low.
My first...
I have a question about the usage of Flash Data Storage, chunks and parsing of the data retrieved from FDS.
How, when and why are you supposed to use "chunks" when setting...
Hello,
I would like to implement an interface with an external SPI ADC using the nRF52832.
The ADC has a RDY (ready) signal that goes low every time a new sample is ready...
Hello,
I have simple custom PCB with nRF51822.
I am trying to make it advertise like a beacon, by program it with ble_app_beacon example from nRF5_SDK examples.
I have...
I'm playing around with the experimental ble hrs with NFC pairing example, and I cannot seem to get it to work with my Android 6.0.1 Moto X Pure. I tap the phone to the NFC...
I have been trying for a long time to implement ble_uart_app with static passkey on SDK 11 s130 on nRF51-dk.
There are a couple of threads on this feature.
devzone.nordicsemi...
I am using ble_app_uart SDK_11 s130 on nRF51-dk.
I want the received characters to be buffered into a string until a new line character is received. The relevant code for...
Hi,
I am trying to attempt the RTT tutorial and I am not able to complete the first task.
I have included the SEGGER_RTT.h deader file, copied RTT and Syscalls folders...
Hi, In my project I need to read a characteristic value, I'm using nRF51822, nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2.0.0_softdevice while I reading it takes around 700ms...
Hi, I'm using ble_app_uart application from latest nRF52 SDK on IAR compiler 7.1 and PCA10040 board.
When opened, it losses all "defined symbols" on Preprocessor tab on...
I am relying on the link below to implement pstorage.
infocenter.nordicsemi.com/index.jsp
I am also using device_manager in my app which may conflict with pstorage....
