Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all,
i'm doing some beaconing experiments with my NRF51-DK, a RFX2411N-EVB and a HG2408U antenna. I'm using S110 with beaconing demo code, and nRF Connect app to measure...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
So having first used Kiel, then Eclipse, it was great to finally ditch my clunky windows laptop with its terribly laid out keyboard by making the transition to Segger Embedded...
hi,
i am integrating c++ library with the ble_app_uart example code. using s130 on pca100028 board. in the make file i have made changes by replacing
CFLAGS += -mthumb ...
I want use pwm driver to generate 8 channel pwm wave with nrf52832， My board is PCA10036. I use example “nRF5_SDK_11.0.0_89a8197\examples\peripheral\pwm_driver\pca10040\arm5_no_packs...
Hi,
Can anyone tell me about fstorage module and can I use this storage space to store password? Will it give me any extra level of security? If so how to implement and...
I use a nRF51 dongle for some tests and I want to map the UART interface of UART_example on the pins 15,16,17 and 18 of the Dongle.
I try to juste adapt this lines of code...
I want to know the architecture of transmitter of nRF51822. I have questions as follows.
Does the block diagram of nRF24L01 show it? (nRF51822 has on-air compatibility...
Hi !
I'm running the ble_app_hrs_freertos example from SDK11 on the nRF52 dev. kit.
I would like to toggle some GPIOs to monitor the CPU activity and the FreeRTOS context...
According to this advertising blog: "The advertiser can use a whitelist to limit the interaction to a number of scanner/central device. The whitelist contains an array of...
I'm developing a custom board with nRF52832. We developed a flexible circuit for NFC antenna, and tuned following the indications on this post on the Nordic blog. Actually...
Hi,
I'm a beginner. I downloaded nRF5 IoT SDK, and tried to run and debug the application "publisher" on nRF52 platform. And each time, I got a message "no source available...
This is what we get from JLinkExe:
Found SWD-DP with ID 0x2BA01477
Could not power-up debug power domain.
Can not connect to target.
This all happens when we use P19...
