Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
I am struggling with the correct value to use for DFU_APP_DATA_RESERVED in the bootloader. My application uses the Device Manager and has one block allocated for to pstorage...
My app is generating hardfualts. Based on this post I looked at memory location SP + 0x14, which points to the address that generated the fault.
Memory at SP+0x14: 8F 31...
Hello Everyone,
I am doing the rough calculation of the power consumption of NRF51 where in the radio part of the datasheet it is indicating 10.5mA whether it is denoted...
Hello ,
I'm using a couple of nRF52 dev.board (one is Nordic preview dev.kit , the other one is a Rigado BMD-300) , with S212 ant+ softdevice . I'm able to deep-slepp the...
I use the board to act as relay.First ,i scan and connect to one peripheral.Then ,i want to disconnect the peirpheral once the another central connect to my board.i call sd_ble_gap_disconnect...
Hi ,
Would you help me to find right material(App note, source code/project) to implement below case:
My nRF51822 connected on beaglebone black(BBB) over UART this will...
Hi,
I want to implement a DC/DC converter setup schematic for my projet and I don't know how to make the difference between the AVDD and VCC_nRF supply tags given in the...
Hi, all!
I have a Quesion about Maximum Voltage & Current of internal DC/DC conv. & LDO of nRF52832.
I'll design circuit using olny internal DC/DC conv. & LDO of nRF52832...
Hi.
Is there a (lazy) (dummy) comfortable way to make an nRF518 chip (in my case, nRF51822) communicate with the built-in bluetooth adapter of a laptop with windows 7 or...
Hi,
I am trying to connect a GPS through UART to nRF52 and get the reading and write it to the serial USB of my PC. I am using app_uart_init() and app_uart_close(). My idea...
Hi, I would like to handle in the twi_event_handler the case when the p_event->type == NRF_DRV_TWI_EVT_EVT_DATA_NACK differently and not treat it as an internal error.
...
I'm trying to use separate antplus network key, but I still can receive messages from devices that are configured with another key. Device A was using network key 0,0,0,0...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
