I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Is it possible to see LOG_INF() or LOG_ERR() messages from custom board software when the custom board is connected to a nRF52840DK through connector P20? The custom board...
I'm concentrating on a work about connecting nrf51-dk device in the sensor node end implementing COAP server, ble enabled rapsberrypi and COAP client using Copper.
To check...
The PPI has been configured to transmit a message every time the timer triggers ( every 1ms).
I'm using IAR Embedded Workbench 7.40.3.8938 as my IDE .
When the system...
Hello all,
Our product based on nRF51 is on preproduction stage. We use both 16MHz and 32kHz external crystals.
The question is:
Is there any way to check programatically...
Dear all,
I do have troubles with the bandwidth of the nRF51822 contained in the Adafruit's Bluefruit LE SPI Friend module. The max. throughput I get is 213 B/s. I'm using...
After doing some DFU work - and it all went fine and dandy ...
I would like to go back to the plain old default bootloader that came with my nRF51 board. I don't seen any...
I'm using IAR IDE for the nordic development of NRF51822 (mdbt40). I'm able to run the example project which does not required soft device. Now i wanted to move further with...
Hi,
Is it possible to program the nRF51-Dongle through the usb, to correspond to Bluetooth content to change GPIO state. Then connect the dongle to an external power source...
Greeting , Nordic team , i have some questions about my project.
First , my hardware and software is following:
nrf51422 (pca10028)
SDK 9.0
SoftDevice S110
My project...
Hi,
I am looking for the possibility of getting an unforgeable unique ID of a bonded device within a BLE connection.
Using nRF51422 with SD310 for the peripheral, any...
Hi, could anyone please help me as I currently using nrf51822-arduino-library in a nrf51822 chip and I couldn't call the interrupt function : wakeUp(). Current I'm connect...
hello,
I want to connect Arduino shield with heart-rate sensor to my nRF 51 DK board.
then i have to receive sensor data continually from the sensor.
my plan is transferring...
Hello there,
I'm currently using nrf52832 with s132 and sdk 0.9.2, based on the 'ble_app_uart' example and keil5. I'm concerned about the current consumption because in...
I am working on nrf52 DK board with eclipse gcc + nRF52 SDK 0.9.2. I found the experimental nfc project but it does not include the gcc make file. I would like to ask:
...
Is there any nRF51 SDK example that used OOB authentication? I'll not have any I/0 or display on peripheral side, and my central will be a mobile app, with connection to internet...
Hi,
Need to know the largest amount of power consumption that the Nordic (nrf52) can consume during the highest power bluetooth mode?
Also, what is the largest power...
