I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I'm trying to accomplish a communication from the nrf24LE1 to the nrf24L01+. The nrf24L01+ is hooked up to an Arduino UNO. The nrf24LE1 is flashed with the "enhanced_shockburst_ptx_nrf24le1...
6.1.4 Erasing a page in code region 1
When erase is enabled, the NVM can be erased page by page using the ERASEPAGE register or the ERASEPCR1
register. After erasing a NVM...
Hello,
I was testing BLE Heart Rate Collector Example with two nRF52832 devices, one was programmed with ble_app_hrs_c as a BLE central role, and the other was programmed...
Hello everyone,
I have very pesky bug that is leaving me in fits. I have a feeling it is a timing issue, but I am not sure at this point. Here is my issue, and I would...
Hi Devzone.
I've taken the ble_app_hrs example,
and then added the example code from the PWM Driver example.
The PWM module is mostly functional,
however I have a...
Hi,
I'm trying to build a SPI Slave <-> BLE bridge, so that everything received over SPI bus is forwarded on BLE and vice versa. In order for the reverse direction to work...
Hello,
i think this is simple question, but nowhere i can find answer. Is nRF52840 preview development kit (PCA10056) contains built in nrf52840 microcontroller or i need...
I am going through the BLE Central tutorial and am a bit confused by the APPL_LOG function calls, from what I could understand it should give messages on serial port, like...
Hello, I have nRF51822 Beacon Kit (pca200006) and nrf51 dk board (pca100028)
I had an impression I could flash beacon and upload new files using nrf51 dk board as jlink over...
I am using IOS nRF Toolbox 4.2 DFU function on nRF51 DK PCA10028. I followed the tutorial here .
Use nRFgo Studio to erase all.
Use nRFgo Studio to program...
We have an nRF51822 peripheral device that is bonded with one and only one central. The central is always an iOS or Android phone running our app, which is scanning at "low...
In the BLE advertising library, in SDK 11, is the timeout for directed slow advertising specified in seconds, or in number of tries?
Seconds would be more consistent with...
Hi All,
I have got a project running on an nRF51422 QFAC, using the lastest SDK.
I am having some problems with the app_timers, i am able to create and start them, and...
Hello all,
i am working with the nRF52832 DK and SDK11. Actually the Enhanced Shock Burst Communication is working. I can send and receive messages. From this point on...
