Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I have recently got a n5 start kit nRF51422. I went through all the set up procedures in the user guide, installed all the correct programs/drivers etc.. My unit...
Hello.
I am looking at the schematic of the nRF51422 USB dongle development kit. The pin P0.30 of the microcontroller is attached to ground. As the pin could potentially...
I'm writing a PC utility in Visual Studio to connect to BLE devices. I'm using the PCA10000 and MasterEmulator.dll. I'm able to discover the services and characteristics of...
Hi NORDIC
I download the example of multilink central (S120) into nrf51822 . I do not know why it can not work ? My SDK is s110_nrf51822_7.0.0_softdevice . Please help...
i am very confused about how to count pulse by using nrf51822? I am going to make a heart rate counter, but i don't know how to config registers to achieve this function....
I can't get a simple application, no soft device, to debug on the nRFDK 10028 board using the I-Jet. I am using the debug in and powering the device from an external power...
Hi
I'm starting with NRF51822. I'm going to develop a costum PCB using this chip. I'm a bit confused because searching on the forum I saw that I need a product key to use...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi all,
I am using the multi role example ( github.com/.../nRF51-multi-role-conn-observer-advertiser) to scan and advertise concurrently.
I was wondering if the scanning...
I have a 16MHz external clock oscillator to drive a micro controller in my system. Can this also be connected to the crystal input on the nRF24L01+ to drive it's clock? Should...
Hi All,
I wanted to write a patient record to glucode measurement charateristics from android Phone which supportes BLE features . How do i write a record to BLE device...
When using the OTA DFU using the button press implementation is it possible for the bootloader to require bonding? I figure I can use the preserve app data functionality built...
Just took the developer.mbed.org/.../ code and run it on the board.
But when I try to connect with my phone I get: "Device doesn't support UART. Disconnecting".
What...
Hello,
I am using the RedBearLab's BLE Shield 2.0 and I'm trying to modify the advertisement data using nRFgo studio to include manufacture data (type: xFF) for one of...
